Abstract:The manufacture method based on the silicon etching process is one of the most important methods to fabricate micro mechanical structure, e.g. micro-engine. In the processing, the high aspect ratio silicon etch process (HARSE process) is very important to improve the efficiency of structure. At the same time, the surface morphology should be controlled exactly to keep the performance of structure. In this paper, the feasibilities of controlling the surface morphology and Si etch rates were experimentally investigated. In the experiments, the width of structure changes from 15um to 1500um and the depth changes from 50um to 500um. The parameters of surface morphology including sidewall angle, surface roughness, and so on were measured and compared. The influence mechanisms of etching parameters were analyzed. The etching process were completed in a surface technology system (STS) multiplex advanced silicon etcher inductively coupled plasma (ICP) system with SF6/O2 plasma as etching plasma and C4F8 as passivation plasma. In the experiments, the etching experiments were conducted in a low pressure (5–50mTorr), high density, inductively coupled plasma etching reactor (ICP) with a planar coil. The Si etches rates and sidewall angle were investigated as a function of chamber pressure, cathode RF-power, and gas flow. The results indicated that the increasing of total etching time results in an acceleration in etch rate as well as the decrease in sidewall angle (the top width of trench is narrow than the bottom width). Meanwhile, the total passivation time has an opposite effect in the influence of etch rate and sidewall angle. All the experiments indicate that the quick shift between etch and passivation period leads to a smoother surface. An interesting phenomenon were discovered that the etch rate will not change with the changing of width parameter in most of the high aspect ratio silicon etch recipes when the width-depth ratio is upper than 0.34. An experiential function formula were fitted based on four parameters, including width and depth of the structure, and total etching and passivation time.

Dynamic Process of Wet Etching Using BOE Solutions to Control the Etch Rate, Roughness, and Surface Morphology of a Z-cut Α-Quartz Wafer

Wet Etching of Quartz Using a Solution Based on Organic Solvents and Anhydrous Hydrofluoric Acid

Deep Reactive Ion Etching of Z-Cut Alpha Quartz for MEMS Resonant Devices Fabrication

Etching of Quartz Crystals in Liquid Phase Environment: A Review

Stable Nanodepth and Nanogram Level Material Removal in Electrochemically Induced Chemical Etching of Fused Quartz

Application of KOH Anisotropic Etching in the Fabrication of MEMS Devices

Research on a Micro-Processing Technology for Fabricating Complex Structures in Single-Crystal Quartz

A One-step Residue-free Wet Etching Process of Ceramic PZT for Piezoelectric Transducers.

A Two-step Wet Etching Process of PZT Thin Film With Ultra-low Undercut for MEMS Applications

Size-Effect-Based Dimension Compensations in Wet Etching for Micromachined Quartz Crystal Microstructures

Wet etching in beta-Ga2O3 bulk single crystals

Effective Approaches to Improve Au Etching Process Performance in MEMS Devices

Wet Etching in β-Ga2O3 Bulk Single Crystal

Cavity Etching Evolution on the A-plane of Sapphire Crystal in Molten KOH Etchant

Etching Quartz with Inductively Coupled Plasma Etching Equipment

Research on Quartz Wet Etching and Flatting Process of Sidewall Arris

Study of anisotropic etching of (1 0 0) Si with ultrasonic agitation

Research on Silicon Wafer Surface Phase under the Ultra-thin Slicing Process and Its Etching Hindrance Behavior during Metal-Assisted Chemical Etching

The Control Method of Surface Morphology and Etch Rates for Silicon Etch Process with Extremely Deep and High Aspect Ratio

Study on Silicon Deep Wet Etching Technology for MEMS

Effect of Surface Hydroxylation on Ultra-Precision Machining of Quartz Glass