Abstract:Bismuth telluride (Bi2Te3)-based alloys are widely used for thermoelectric cooling and power generation at low temperatures, and they are the only commercially available materials for thermoelectric applications below 500 K. The rhombohedral unit cell with a large c/a lattice constant ratio consisting of - Te-Bi-Te-Bi-Te- stacked layers inevitably brings about a large anisotropy in transport properties, which is why texturing is very important in polycrystalline Bi2Te3</sub alloys for maximum performance. In this report, p and n-type polycrystalline Bi2Te3</sub alloys were synthesized and hot-deformed to investigate the effects of texturing on thermoelectric properties. Hot deformation (HD) induces the strong alignment of (001) orientations along the compression direction, and a remarkable increase in the orientation factor F of (001) orientations is observed after HD in both p and n-type materials. All of the hot-deformed polycrystalline samples showed increased electrical conductivity (σ), power factor (PF), and thermal conductivity (k) in the in-plane (IP) direction, and vice versa in the out-of-plane (OOP) direction, which makes the IP direction of the hot-deformed bodies more favorable for module fabrication in terms of power factor, for both p and n-type Bi2Te3</sub-based alloys. However, due to the different degree of anisotropy of k and σ, the figures of merit (zT) were maximized in the OOP direction in the p-type materials after HD, whereas the zTs of the n-type materials were higher in the IP direction. This occurs because the anisotropy factor of electron conduction is higher than that of hole conduction, which more than offsets the advantage of the smaller k in the c-direction of n-type Bi2Te3</sub. The maximum zT of 1.33 (OOP) and 0.90 (IP) were obtained after HD from the p and n-type Bi2Te3 alloys, respectively, which were 9.3% and 18.4% higher than those of as-sintered materials.

Hot Deformation Induced Multi-scale Microstructure Effect in High-performance Bismuth Telluride Based Thermoelectric Material

Enhancement in thermoelectric performance of bismuth telluride based alloys by multi-scale microstructural effects

Improving Thermoelectric Properties of N-Type Bismuth–telluride-Based Alloys by Deformation-Induced Lattice Defects and Texture Enhancement

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Tuning Multiscale Microstructures to Enhance Thermoelectric Performance of N‐type Bismuth‐Telluride‐Based Solid Solutions

Liquid‐Phase Hot Deformation to Enhance Thermoelectric Performance of N‐type Bismuth‐Telluride‐Based Solid Solutions

Evolution of the Intrinsic Point Defects in Bismuth Telluride-Based Thermoelectric Materials

Enhanced Thermoelectric and Mechanical Properties of Zone Melted P-Type (bi,sb)2te3 Thermoelectric Materials by Hot Deformation

Hot Deformation Induced Bulk Nanostructuring of Unidirectionally Grown P-Type (Bi,sb)(2)te-3 Thermoelectric Materials

Multi-scale hierarchical microstructure modulation towards high room temperature thermoelectric performance in <i>n</i>-type Bi<sub>2</sub>Te<sub>3</sub>-based alloys

Microstructure Evolution in Plastic Deformed Bismuth Telluride for the Enhancement of Thermoelectric Properties

Enhancing Thermoelectric Performance of N-Type Hot Deformed Bismuth-Telluride-Based Solid Solutions by Nonstoichiometry-Mediated Intrinsic Point Defects.

High Pressure Drives Microstructure Modification and zT Enhancement in Bismuth Telluride-Based Alloys

Recrystallization Induced in Situ Nanostructures in Bulk Bismuth Antimony Tellurides: a Simple Top Down Route and Improved Thermoelectric Properties

Analysis of Thermoelectric Properties of Hot-deformed Bismuth Telluride Sintered Materials

Hot Deformation Induced Defects and Performance Enhancement in FeSb2 Thermoelectric Materials

Point Defect Engineering of High‐Performance Bismuth‐Telluride‐Based Thermoelectric Materials

High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys

High-performance near-room-temperature n-type Bi2Te3-based thermoelectric alloys with superior mechanical properties

Enhanced thermoelectric performance of n-type bismuth-telluride-based alloys via In alloying and hot deformation for mid-temperature power generation

Deformation behavior and mechanism of p-type (Bi,Sb) 2 Te 3 alloy during three-point bending test at room temperature