Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400–500 °C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large-scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 °C. At the optimal sintering temperature (130 °C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8–1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.5Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m–1 K–1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03540.Single parabolic band model and calculated transport properties; EBSD analysis for pellet sintered at 110 °C; BSE, EDS mapping, and TEM images of pellet sintered at 130 °C; average ZT values; and XPS results (PDF)This article has not yet been cited by other publications.

Hot Deformation Induced Bulk Nanostructuring of Unidirectionally Grown P-Type (Bi,sb)(2)te-3 Thermoelectric Materials

Enhanced Thermoelectric and Mechanical Properties of Zone Melted P-Type (bi,sb)2te3 Thermoelectric Materials by Hot Deformation

Liquid‐Phase Hot Deformation to Enhance Thermoelectric Performance of N‐type Bismuth‐Telluride‐Based Solid Solutions

Enhancement in thermoelectric performance of bismuth telluride based alloys by multi-scale microstructural effects

Recrystallization Induced in Situ Nanostructures in Bulk Bismuth Antimony Tellurides: a Simple Top Down Route and Improved Thermoelectric Properties

Improving Thermoelectric Properties of N-Type Bismuth–telluride-Based Alloys by Deformation-Induced Lattice Defects and Texture Enhancement

Achieving High Thermoelectric Performance of n-Type Bi 2 Te 2.79 Se 0.21 Sintered Materials by Hot-Stacked Deformation

High-performance near-room-temperature n-type Bi2Te3-based thermoelectric alloys with superior mechanical properties

Modulation of Vacancy Defects and Texture for High Performance N-Type Bi2 Te3 Via High Energy Refinement.

Modulation of Vacancy Defects and Texture for High Performance n‐Type Bi2Te3 via High Energy Refinement

Tuning Multiscale Microstructures to Enhance Thermoelectric Performance of N‐type Bismuth‐Telluride‐Based Solid Solutions

Multi-scale hierarchical microstructure modulation towards high room temperature thermoelectric performance in <i>n</i>-type Bi<sub>2</sub>Te<sub>3</sub>-based alloys

Enhancing Thermoelectric Performance of N-Type Hot Deformed Bismuth-Telluride-Based Solid Solutions by Nonstoichiometry-Mediated Intrinsic Point Defects.

Attaining high mid-temperature performance in (Bi,Sb) 2 Te 3 thermoelectric materials via synergistic optimization

Enhanced thermoelectric performance of orientated and defected SnTe

Hot Deformation Induced Multi-scale Microstructure Effect in High-performance Bismuth Telluride Based Thermoelectric Material

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Dramatic Enhancement of Thermoelectric Performance in PbTe by Unconventional Grain Shrinking in Sintering Process

High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys

Nanostructuring and improved performance of ternary Bi–Sb–Te thermoelectric materials

Thermoelectric Performance Enhancement in N -Type Bi 2 (tese) 3 Alloys Owing to Nanoscale Inhomogeneity Combined with a Spark Plasma-Textured Microstructure