Abstract:Bismuth telluride (Bi2Te3)-based alloys are widely used for thermoelectric cooling and power generation at low temperatures, and they are the only commercially available materials for thermoelectric applications below 500 K. The rhombohedral unit cell with a large c/a lattice constant ratio consisting of - Te-Bi-Te-Bi-Te- stacked layers inevitably brings about a large anisotropy in transport properties, which is why texturing is very important in polycrystalline Bi2Te3</sub alloys for maximum performance. In this report, p and n-type polycrystalline Bi2Te3</sub alloys were synthesized and hot-deformed to investigate the effects of texturing on thermoelectric properties. Hot deformation (HD) induces the strong alignment of (001) orientations along the compression direction, and a remarkable increase in the orientation factor F of (001) orientations is observed after HD in both p and n-type materials. All of the hot-deformed polycrystalline samples showed increased electrical conductivity (σ), power factor (PF), and thermal conductivity (k) in the in-plane (IP) direction, and vice versa in the out-of-plane (OOP) direction, which makes the IP direction of the hot-deformed bodies more favorable for module fabrication in terms of power factor, for both p and n-type Bi2Te3</sub-based alloys. However, due to the different degree of anisotropy of k and σ, the figures of merit (zT) were maximized in the OOP direction in the p-type materials after HD, whereas the zTs of the n-type materials were higher in the IP direction. This occurs because the anisotropy factor of electron conduction is higher than that of hole conduction, which more than offsets the advantage of the smaller k in the c-direction of n-type Bi2Te3</sub. The maximum zT of 1.33 (OOP) and 0.90 (IP) were obtained after HD from the p and n-type Bi2Te3 alloys, respectively, which were 9.3% and 18.4% higher than those of as-sintered materials.

Improving Thermoelectric Properties of N-Type Bismuth–telluride-Based Alloys by Deformation-Induced Lattice Defects and Texture Enhancement

Enhancement in thermoelectric performance of bismuth telluride based alloys by multi-scale microstructural effects

Liquid‐Phase Hot Deformation to Enhance Thermoelectric Performance of N‐type Bismuth‐Telluride‐Based Solid Solutions

Enhancing Thermoelectric Performance of N-Type Hot Deformed Bismuth-Telluride-Based Solid Solutions by Nonstoichiometry-Mediated Intrinsic Point Defects.

Thermoelectric Enhancements in PbTe Alloys Due to Dislocation‐Induced Strains and Converged Bands

Enhanced Thermoelectric and Mechanical Properties of Zone Melted P-Type (bi,sb)2te3 Thermoelectric Materials by Hot Deformation

Hot Deformation Induced Multi-scale Microstructure Effect in High-performance Bismuth Telluride Based Thermoelectric Material

High-performance near-room-temperature n-type Bi2Te3-based thermoelectric alloys with superior mechanical properties

Enhancing room temperature thermoelectric performance of n-type polycrystalline bismuth-telluride-based alloys via Ag doping and hot deformation

Hot Deformation Induced Bulk Nanostructuring of Unidirectionally Grown P-Type (Bi,sb)(2)te-3 Thermoelectric Materials

Recrystallization Induced in Situ Nanostructures in Bulk Bismuth Antimony Tellurides: a Simple Top Down Route and Improved Thermoelectric Properties

Synergistic Compositional–Mechanical–Thermal Effects Leading to a Record High Zt in N‐type V2VI3 Alloys Through Progressive Hot Deformation

Substitutions and Dislocations Enabled Extraordinary N-Type Thermoelectric PbTe

Achieving High Thermoelectric Performance of n-Type Bi 2 Te 2.79 Se 0.21 Sintered Materials by Hot-Stacked Deformation

Enhancing room-temperature thermoelectric performance of n-type Bi2Te3-based alloys via sulfur alloying

Manipulation of Band Degeneracy and Lattice Strain for Extraordinary PbTe Thermoelectrics

Enhanced thermoelectric performance of n-type bismuth-telluride-based alloys via In alloying and hot deformation for mid-temperature power generation

Tuning Multiscale Microstructures to Enhance Thermoelectric Performance of N‐type Bismuth‐Telluride‐Based Solid Solutions

Analysis of Thermoelectric Properties of Hot-deformed Bismuth Telluride Sintered Materials

Atomic Disordering Advances Thermoelectric Group IV Telluride Alloys with a Multiband Transport

Multi-scale hierarchical microstructure modulation towards high room temperature thermoelectric performance in <i>n</i>-type Bi<sub>2</sub>Te<sub>3</sub>-based alloys