Abstract:The abundance of low-temperature waste heat produced by industry and automobile exhaust necessitates the development of power generation with thermoelectric (TE) materials. Commercially available bismuth telluride-based alloys are generally used near room temperature. Materials that are composed of p-type bismuth telluride, which are suitable for low-temperature power generation (near 380 K), were successfully obtained through Sb-alloying, which suppresses detrimental intrinsic conduction at elevated temperatures by increasing hole concentrations and material band gaps. Furthermore, hot deformation (HD)-induced multi-scale microstructures were successfully realized in the high-performance p-type TE materials. Enhanced textures and donor-like effects all contributed to improved electrical transport properties. Multiple phonon scattering centers, including local nanostructures induced by dynamic recrystallization and high-density lattice defects, significantly reduced the lattice thermal conductivity. These combined effects resulted in observable improvement of ZT over the entire temperature range, with all TE parameters measured along the in-plane direction. The maximum ZT of 1.3 for the hot-deformed Bi0.3Sb1.7Te3 alloy was reached at 380 K, whereas the average ZTav of 1.18 was found in the range of 300–480 K, indicating potential for application in low-temperature TE power generation. Thermoelectric materials, which convert temperature differences and electric voltage into each other, serve in refrigeration or power generation applications. Currently, bismuth telluride (Bi2Te3) and its alloys are the most widely used thermoelectric materials. Tie-Jun Zhu, Xin-Bing Zhao and co-workers from Zhejiang University, China, have now investigated the effect of antimony (Sb) alloying on bismuth tellurides through a series of polycrystalline solid solutions of Bi2-xSbxTe3—where x varies between 1.4 and 1.8—prepared by hot deformation. Systematic tuning of the alloy composition showed that higher antimony content raised the material's optimal conversion temperature by repressing undesirable conduction. This effect arises from an increase in both the hole concentration and the band gap in the material. For a composition where x is 1.7, the alloy showed optimal performances at 380 kelvin—a suitable temperature for low-temperature power generation from the waste heat generated by industry or vehicles. The p-type bismuth telluride-based polycrystalline materials suiting for low-temperature power generations (near 380 K) have been obtained through Sb-alloying and HD, which suppresses the detrimental effect of intrinsic conduction at elevated temperature via increasing the hole concentration and band gap. The hot-deformed Bi0.3Sb1.7Te3 alloy, not usual composition Bi0.5Sb1.5Te3, shows a maximum ZT of 1.3 at 380 K, indicating a bright application potential in low-temperature power generations.

Enhanced thermoelectric performance of n-type bismuth-telluride-based alloys via In alloying and hot deformation for mid-temperature power generation

Shifting Up the Optimum Figure of Merit of P-Type Bismuth Telluride-Based Thermoelectric Materials for Power Generation by Suppressing Intrinsic Conduction

Enhancing room temperature thermoelectric performance of n-type polycrystalline bismuth-telluride-based alloys via Ag doping and hot deformation

Enhanced Thermoelectric and Mechanical Properties of Zone Melted P-Type (bi,sb)2te3 Thermoelectric Materials by Hot Deformation

Improved thermoelectric properties of zone-melted p-type bismuth-telluride-based alloys for power generation

Attaining high mid-temperature performance in (Bi,Sb) 2 Te 3 thermoelectric materials via synergistic optimization

Mid-temperature Thermoelectric Performance of Zone-Melted Sb2(Te,Se)3 Alloys Near Phase Transition Boundary

Enhanced Figure of Merit in Antimony Telluride Thermoelectric Materials by In–Ag Co-Alloying for Mid-Temperature Power Generation

Enhancement in thermoelectric performance of bismuth telluride based alloys by multi-scale microstructural effects

Enhanced mechanical and thermoelectric properties enabled by hierarchical structure in medium-temperature Sb2Te3 based alloys

High-performance near-room-temperature n-type Bi2Te3-based thermoelectric alloys with superior mechanical properties

Thermoelectric Performance of P-Type Zone-Melted Se-doped Bi 0.5 Sb 1.5 Te 3 Alloys

Enhancing room-temperature thermoelectric performance of n-type Bi2Te3-based alloys via sulfur alloying

Enhancing Thermoelectric Performance of N-Type Hot Deformed Bismuth-Telluride-Based Solid Solutions by Nonstoichiometry-Mediated Intrinsic Point Defects.

High Performance BiSbTe Alloy for Superior Thermoelectric Cooling

High Performance N-Type Bismuth Telluride Based Alloys for Mid-Temperature Power Generation

Multi-scale hierarchical microstructure modulation towards high room temperature thermoelectric performance in <i>n</i>-type Bi<sub>2</sub>Te<sub>3</sub>-based alloys

Synergistic effects of B-In codoping in zone-melted Bi0.48Sb1.52Te3-based thermoelectric

Tunable Optimum Temperature Range of High-Performance Zone Melted Bismuth-Telluride-Based Solid Solutions

Liquid‐Phase Hot Deformation to Enhance Thermoelectric Performance of N‐type Bismuth‐Telluride‐Based Solid Solutions

Sb2Te3 based alloy with high thermoelectric and mechanical performance for low-temperature energy harvesting