Abstract:Ni–SiC nanocomposite coatings were prepared on a brass substrate by electrocodeposition. The electrodeposition was carried out by adding the SiC nanoparticles to a nickel-containing bath. Nickel deposition processes were analyzed by cathodic polarization curves, and the plating parameters were determined preliminarily by analyzing the effects of different technological parameters on the deposition process. Then, electrocodeposition processes were carried out with different concentrations of SiC nanoparticles in the bath. The effects of current density, stirring rate, and SiC nanoparticle’s concentration in the plating bath on the hardness of coatings were investigated by microhardness tests. Besides the microhardness tests, wearing tests and corrosion tests were also applied to the coatings with the highest hardness and coatings of pure nickel. The structures and surface morphologies of the coatings were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The experimental results show that the microhardness of the codeposited coating increases with increasing current density and attains a maximum at the SiC concentration of 6 g/L. The decrease in the microhardness at higher SiC concentrations may be due to agglomeration of nanosized particles in the plating bath. Increasing the stirring speed did not give a better quality deposition as coatings produced at low stirring rates always had higher microhardness values than did those at high stirring rates. Furthermore, the Ni–SiC nanocomposite coatings have lower friction coefficient and better corrosion resistance than those of pure nickel coatings.

Ni-Ce-P Electroless Plating and Properties of the Coating on 27simn Steel

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Electroless Deposition of Ni-Co-P Deposit on NdFeB Permanent Magnets and Its Corrosion Resistance Property

Preparation of Ni-Coated SiC Ceramic Composite Powder by Electroless Plating

Electroless Co-P Alloy Plating of Superfine Si3N4 Powders

CHEMICAL PLATING MECHANISM IN ACID BATHS AND FABRICATION OF Ni-P COATING WITH HIGH P CONTENT

Mechanically Assisted Electroless Barrel-Plating Ni-P Coatings Deposited on Carbon Steel

A Study on the Electrocodeposition Processes and Properties of Ni–SiC Nanocomposite Coatings

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

The Research on Coating of Electroless Ni-W-P Ternary Alloys

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Electrochemical Synthesis and Characterization of Ni–P Alloy Coatings from Eutectic–Based Ionic Liquid

Study of properties of Ni-base nano-ZrO2 composite plating coatings

Preparation of Ni-P-Ti3C2Tx-Ce composite coating with enhanced wear resistance and electrochemical corrosion behavior on the surface of low manganese steel

Effect of Heat Treatment on Chemical Plating of Ni-Cr-P on 65Mn Alloy Steel

Influence of Electrodeposition Process Parameters and Si3N4 Nanoparticle Concentration on Microhardness and Wettability of Ni-Co-Si3N4 Nanocomposite Coatings

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Preparation of Amorphous Nickel-Phosphorus Alloy Coating by Electroplating

Study on Properties of Double-Layered Ni–P–Cr Composite Coating Prepared by the Combination of Electroless Plating and Pack Cementation

Preparation and characterization of Ce-sealed Ni-P coating for a nickel-based superalloy

Preparation and Characterization of Ni-Coated Cr3c2 Powder by Room Temperature Ultrasonic-Assisted Electroless Plating