Abstract:The multilayer graphene (MLG) reinforced WC-10Ni 3 Al cemented carbide was prepared by microwave sintering. The effects of the sintering temperature and MLG content on the microstructure and mechanical properties of the WC-10Ni 3 Al cemented carbide were investigated. The promotion effect and strengthening mechanism of MLG on WC-10Ni 3 Al by microwave sintering were explored. The tribological properties of WC-10Ni 3 Al and Ti6Al4V(TC4) were studied, and the wear mechanism of WC-10Ni 3 Al was revealed. The experiment result show that the WC-10Ni 3 Al-0.5 wt.% MLG sample sintered at 1450°C had its greatest mechanical properties with a relative density of 96.9%, hardness of 1430 HV, flexural strength of 1410 MPa and fracture toughness of 15.7 MPa·mm 1/2 , which were 4.2%, 12.2%, 24.4%, and 29.6% greater than those of the sample without MLG added, respectively. The reinforcing and toughening mechanisms of adding MLG in WC-10Ni 3 Al samples consist of fine crystal strengthening, crack bridging and deflection, MLG pulling out and bridging. The results of friction experiment show that the friction coefficient and wear rate of the WC-10Ni 3 Al samples were lower than those of YG8 (WC-8 wt. % Co cemented carbide). The WC-10 Ni 3 Al-0.5 wt.% MLG sample obtained the lowest friction coefficient of 0.35 and the lowest wear rate of 1.69 × 10 -5 mm 3 N -1 m -1 . A stable solid lubrication film was produced on the friction surface of the WC-10Ni 3 Al samples, which was conducive to reducing the breakage and wear of WC grains. MLG can enhance the stability of solid lubrication film and reduce its friction coefficient.

Research on Microstructure and Properties of Ultrafine Grained WC-Ni3Al Cemented Carbide

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Effect of Nano-AlN Addition on the Microstructure and Mechanical Properties of Binderless WC-VC-TaC-AlN Cemented Carbides

Effect of WC grain size on mechanical properties and microstructures of cemented carbide with medium entropy alloy Co-Ni-Fe binder

Effect of Metal Elements on Microstructure and Mechanical Properties of Ultrafine Cemented Carbide Prepared by SPS

Effects of nanocomposite grain growth inhibitors and multi-walled carbon nanotubes on the microstructure and mechanical properties of ultrafine cemented carbides

Peculiarities of Preparation and Properties of Cemented Carbide WC + 20 Mass% Ni with Ultra-Coarse-Grained Microstructure

Ultrafine WC-Ni cemented carbides fabricated by spark plasma sintering

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Microstructure, mechanical and tribological properties of multilayer grapheme reinforced WC-10Ni 3 Al prepared by microwave sintering

Effect of particle size and high-energy ball milling time on microstructure and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

Microstructure and mechanical properties of WC–Co-based cemented carbide with bimodal WC grain size distribution

Microstructure and properties of ultrafine WC–Co–VC cemented carbides with different Co contents

Effects of nano-alumina on mechanical properties and wear resistance of WC-8Co cemented carbide by spark plasma sintering

Effects of micro/nano CeO2 on the microstructure and properties of WC-10Co cemented carbides