Abstract:<p>A circumferential crack in the fusion line is a major threat to the structural integrity of the pipeline girth weld because it may possibly lead to fracture failure when subjected to large plastic deformations. For the newly constructed X80 pipeline with an outside diameter (OD) of 1422 mm in China, the complicated configuration of welded joints and the outer diameter are outside the range of the general fracture assessment standards, such as BS 7910. Furthermore, during the pipe manufacture process, pipeline designers merely specify the minimum yield strength limit according to the pipe steel grade. This results in a wide variation range in the choice of yield strength values of the base metal. This also leads to a serious problem in the fracture assessment of pipe girth weld because the weld strength is commonly considered to be either evenly matched or overmatched. The foregoing factors make it difficult to perform an accurate fracture assessment using conventional standards. This study therefore aims to investigate the fracture behavior of 1422-mm OD pipelines with a double-V groove weld and circumferential crack in the fusion line. The specific effect of material mismatch and the realistic operational parameters that influence the fracture capacity of the pipe are examined via a series of numerical investigations. First, a rigorous three-dimensional finite element model to simulate the pipe girth weld is established by utilizing the ABAQUS finite element code package. The weld, which has a canoe-shaped surface crack in the fusion line between the heat-affected zone and root welding metal, is subjected to biaxial loading conditions. The keyhole method is adopted to simulate the crack front as well as the crack tip to eliminate the stress singularity effect during deformation. A refined mesh strategy is introduced to ensure the accurate simulation of the stress and strain fields in the vicinity of the crack tip. Based on the numerical model, the J-integral fracture parameter, which is clearly defined based on a strict mechanical theory, is chosen to characterize the effect of strength matching ratio, internal pressure, and yield to tensile strength ratio on the crack driving force. A new strain-based J-integral prediction formula is proposed based on numerical results.</p>

Effect of Strength Mismatch on Ductile Fracture Behavior of Welding Pipe

Mismatch effect on safety assessment of pressure pipe with incomplete penetration defect

Strength Differential Effect and Influence of Strength Criterion on Burst Pressure of Thin-Walled Pipelines

Numerical Investigation of the Influence of Ultimate-Strength Heterogeneity on Crack Propagation and Fracture Toughness in Welded Joints

Inhomogeneous Strain Behaviors of the High Strength Pipeline Girth Weld under Longitudinal Loading

Effect of welding axial stresses on the strength of a welded pipe joint with a defect

Effect of Yield Strength Distribution Welded Joint on Crack Propagation Path and Crack Mechanical Tip Field

Effect of Welding Defects on Mechanical Properties of Welded Joints Subjected to Temperature

Fracture prediction in transverse fillet welded joints of high strength structural steel

Effect of Inhomogeneous Mechanical Properties on the Stress-Strain Field at the Crack Tip and Crack Growth Direction in Dissimilar Metal Welded Joints

Effect of Mechanical Heterogeneity on Strain and Stress Fields at Crack Tips of SCC in Dissimilar Metal Welded Joints

Fracture driving forces of cracked girth welds with mechanical heterogeneity for X80 pipes

Research On Safety Assessment Method For Pressure Pipe With Incomplete Welding Defects Under Complicated Loadings

Fracture response of 1422-mm diameter pipe with double-V groove weld joints and circumferential crack in fusion line

Mechanical behaviour of longitudinal lap-welded joints of high strength steel: Experimental and numerical analysis

RETRACTED: Investigation of Ductile Fracture Behavior of Lap-Welded Joints with 460 MPa Steel

Influence of Material Model on Prediction Accuracy of Welding Residual Stress in an Austenitic Stainless Steel Multi-pass Butt-Welded Joint

Analysis of influence of initial gap of laser-arc hybrid butt welds on inherent strain and welding deformation of a pipe structure

Fracture behavior analysis of X80 pipelines welded joints with unequal wall thickness

Characterization of heterogeneous mechanical properties for thick welded joints with flow stress variation in the transverse and thickness directions

Investigation of the Fracture Behavior of High-Strength Structural Steel and Welds Based on Micromechanical Models