Abstract:Stress corrosion cracking (SCC) is a major problem in the welded components of austenitic stainless steel in nuclear power plants. High tensile residual stress is an important factor resulting in the SCC of materials. Austenitic stainless steel has a strong tendency for work hardening owing to its fcc crystal structure and low stacking-fault energy. High plastic strain can accumulate during a multipass welding process. On the other hand, accumulated strain hardening can be reduced or even eliminated during the welding thermal cycles owing to dynamic recovery, recrystallization, and grain growth below the melting point, which is called the annealing effect. Influence of strain hardening and annealing effect needs to be investigated to predict the welding-induced residual stresses accurately in austenitic stainless steel joints. In this study, a new time-temperature-dependent annealing model was proposed based on the Johnson-Mehl-Avrami equation. Numerical Satoh tests were performed to clarify the influence of strain-hardening models (i.e., the isotropic strain-hardening model and Chaboche mixed isotropickinematic strain-hardening model) and annealing models (i. e., the single-stage annealing model and new time-temperature-dependent annealing model) on the formation of residual stresses and the accumulated plastic strain during multiple thermal cycles. Thermoelastic-plastic finite element (FE) analyses were carried out to predict the welding residual stresses and accumulated plastic strain in a thick-wall 316 stainless steel butt-welded pipe joint with 85 welding passes. The residual stresses of the welded joint were measured by the sectioning method, inherent strain method, and deep-hole drilling method. The simulations of welding residual stresses were compared with the measurements. Annealing effect significantly influences the formation of accumulated plastic strain and welding residual stresses, neglecting which will result in a significant overestimation of FE results. The proposed annealing model showed an excellent match to the experimental data. With the consideration of the annealing effect, the isotropic strain-hardening model overestimated the welding residual stresses slightly, while the FE results of welding residual stresses using the Chaboche mixed strain-hardening model showed better agreement with the measurements. The single-stage annealing model revealed a recommended annealing temperature of 900-1000 degrees C for austenitic stainless steel such as 316 stainless steel.

Influence of Material Model on Prediction Accuracy of Welding Residual Stress in an Austenitic Stainless Steel Multi-pass Butt-Welded Joint

Influence of Strain Hardening and Annealing Effect on the Prediction of Welding Residual Stresses in a Thick-Wall 316 Stainless Steel Butt-Welded Pipe Joint

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

Simulating Welding Residual Stress and Deformation in a Multi-Pass Butt-Welded Joint Considering Balance Between Computing Time and Prediction Accuracy

INFLUENCE OF ANNEALING TEMPERATURE ON CALCULATION ACCURACY OF WELDING RESIDUAL STRESS IN A SUS304 STAINLESS STEEL JOINT

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Numerical and Experimental Investigations on Welding Residual Stress in Multi-Pass Butt-Welded Austenitic Stainless Steel Pipe

Influence of Lumped-pass Method on Calculation Accuracy and Efficiency of Welding Residual Stress in SUS304 Stainless Steel Butt Joints

Modeling of welding residual stress in a dissimilar metal butt-welded joint between P92 ferritic steel and SUS304 austenitic stainless steel

Modeling of Hardness and Welding Residual Stress in Type 316 Stainless Steel Components for the Assessment of Stress Corrosion Cracking

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

FEM Analysis of Residual Stress Induced by Repair Welding in SUS304 Stainless Steel Pipe Butt-Welded Joint

Influences of Dimension Factors on Residual Stress and Welding Distortion in SUS304 Stainless Steel Butt Joint

Influence of Size Factor on Calculation Accuracy of Welding Residual Stress of Stainless Steel Pipe by 2D Axisymmetric Model

Numerical and experimental study on thermal-metallurgical-mechanical behavior of high-strength steel welded joint

Prediction of Welding Residual Stress in Multi-Pass Butt-Welded Modified 9cr–1mo Steel Pipe Considering Phase Transformation Effects

Numerical Simulation and Development of Efficient Calculation Method for Residual Stress of SUS316 Saddle Tube-Pipe Joint

Numerical Simulation of Welding Residual Stresses in A Multi-Pass Butt-Welded Joint of Austenitic Stainless Steel Using Variable Length Heat Source

Strength Mismatch Effect on Residual Stress of High Strength Steel Butt-Welded Joints

Investigation of Welding Residual Stress Distribution in a Thick-Plate Joint with an Emphasis on the Features Near Weld End-Start

Predicting Welding Residual Stresses in A Dissimilar Metal Girth Welded Pipe Using 3d Finite Element Model with A Simplified Heat Source