Fault Analysis and Preventive Measures of Current Transformer

Zhong-yuan CHEN,Yan-wei WANG,Jie MENG,Yang ZHANG

DOI: https://doi.org/10.19487/j.cnki.1001-8425.2017.09.016

2017-01-01

Abstract:The typical current transformer faults are enumerated by the authors in this paper.Through the analysis and the disintegration inspection,the causes of the accident and the abnormal data are found out.

What problem does this paper attempt to address?

Probe into a fault cause of 220kV current transformer

Lijun Fu,Weiwei Liu,Jian Zhang,Jianquan Liang,Lei Wang,Liang Zhang,Yanling Guan,Bing Wei

2022-01-01

Abstract:The reliability of current transformer operation is directly related to the safe and stable operation of power grid. This paper introduces a 220 kV current transformer oil level abnormal fault, in order to ensure the safe and stable operation of the power grid and to avoid the occurrence of accidents, the content of dissolved gas in insulating oil was detected for other current transformers made by the same manufacturer of fault current transformer, and abnormal conditions were found. In order to find out the cause of the fault, the fault current transformer was checked and disassembled at the factory, and several problems were found in the vacuum drying of the equipment and the primary insulation of the equipment, the partial overheat water decomposition and partial discharge occur in the operation of the equipment. With the increase of partial discharge and overheat, the insulation oil will deteriorate and a lot of gas will precipitate out. According to the reason of failure, the corresponding preventive measures are put forward.
Research of the Coupling Transformer in the New Bridge-Type Solid State Fault Current Limiter System

Yingying Yao,Dong Wang,Daozuo Jiang,Zhaolin Wu

DOI: https://doi.org/10.3969/j.issn.1001-4551.2007.08.027

2008-01-01

Abstract:This paper proposes a method for analysis and design of the coupling transformer in the new bridge-type solid state fault current limiter (SSFCL). magnetic-circuit coupled FEM is used to investigate the transformer under power system. Being different from the traditional design rule, the proposed transformer is designed under special way. It not only results in the SSFCL run in the power net effectively, but also limits the short-circuit current substantially. Comparing with the normal transformer and SSFCL, the new one has many advantages, such as small volume, low cost, and has good application prospect.
Design and Realization of Power Equipment Current-carrying Faults Intelligent Warning System

黑颖顿,鲁二峰,许力

DOI: https://doi.org/10.3969/j.issn.1001-182X.2013.02.027

2013-01-01

Abstract:Current-carrying fault is one of the most popular faults of power equipments.When carrier fault occurs the contactor's temperature is higher than normal values and lead to serious result.However,the traditional methods can only do simple threshold determination,and failed to effectively extract valuable information and the diagnosis results are always unsatisfactory.To solve the problem,a new intelligent diagnosis method is proposed in this paper.Furthermore the intelligent warning system is designed and developed for power equipment current-carrying fault,and it's working principle,structure and performance are elaborated.
Diagnostic System for Current-Carrying Fault: Modeling, Precaution, and Prediction

Huiyuan Zhang,Li Xu

DOI: https://doi.org/10.1109/tpwrd.2013.2295005

IF: 4.825

2014-01-01

IEEE Transactions on Power Delivery

Abstract:This paper presents a novel method based on heat-transfer theory, principal component analysis (PCA), and particle filtering (PF) to detect, trace, and predict current-carrying faults in electrical equipment. Based on heat-transfer theory, a model is proposed to describe the temperature rise of a faulty contact. PCA is applied to analyze each contact's real-time temperature sequence and categorize faulty contacts for early warnings. After fault detection, the temperature sequence of a faulty contact is extracted and adopted to initialize the model parameters. To better demonstrate the fault status, PF is utilized to optimize the model parameters. Experimental results are presented to verify the feasibility and validity of the proposed method.
An online diagnosis method for the inter-turn fault of current transformer based on ΔI-E curves

Shaoping Zhou,Pingan Wei,Xiang Li,Lan Jiang

DOI: https://doi.org/10.1088/1742-6596/2656/1/012028

2023-12-13

Journal of Physics Conference Series

Abstract:The inter-turn short fault of the secondary coil is the most frequent fault for current transformers. Failure to detect this fault promptly will affect the accuracy of electrical measurement and the correctness of relay protection actions. This paper proposes an online diagnosis method for inter-turn short faults in current transformers. A ΔI-E curve is constructed based on the real signal of the primary winding and the measurement signal of the secondary winding. The working condition of the current transformer is reflected by the change in the curve. Simulation results show that the proposed method can detect the inter-turn short fault of the current transformer online and sensitively, which has certain practical value.
Analysis on Reliability of Electronic Current Transformer Based on Failure Modes,Effects Analysis and Fault Tree Analysis

WANG Peng,ZHANG Gui-xin,ZHU Xiao-mei,LUO Cheng-mu,GU Li-hua

DOI: https://doi.org/10.3321/j.issn:1000-3673.2006.23.004

2006-01-01

Abstract:Reliability analysis is the key procedure during the development of electronic current transformer (ECT). On the basis of the contrastive analysis on reliability of electromagnetic current transformers, by means of failure modes and effects analysis (FMEA) as well as fault tree analysis (FTA) the reliability of a kind of electronic current transformer is researched, and perfect worksheets of both FMEA and FTA are established. All of minimum cut sets of fault trees are found out and the qualitative analysis on the reliability of the ECT is conducted. The effectiveness of the presented reliability analysis method is verified by the results of the analysis on two practical examples during the development and test process of the ECT.
Early Warning Of Current-Carrying Faults Based On Deterioration Assessment Of Electric Contacts

Xin He,Li Xu,Zhe Zhang

DOI: https://doi.org/10.1002/tee.22786

IF: 0.923

2018-01-01

IEEJ Transactions on Electrical and Electronic Engineering

Abstract:This article presents a novel early warning approach of current-carrying faults of electric equipment based on the deterioration assessment of electric contacts. We propose to detect the temperature diversity among three phases at a certain site by employing the singular entropy analysis to the temperature sequences. Then, power spectrum density is employed to analyze the deterioration and to locate the potential faulty contacts while accomplishing the precaution task. Experimental results are presented to verify the feasibility and validity of the proposed method. (c) 2018 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.
Temperature Model of Electrical Equipment and Its Application in Trend Forecast for Current-Carrying Fault

ZHANG Hui-yuan,SHEN Jun-da,XU Li

DOI: https://doi.org/10.3969/j.issn.1007-449x.2013.07.013

2013-01-01

Abstract:Current-carrying fault is one of the most common faults of electrical equipment,which could be detected from temperature change in related parts.In order to comprehend and predict the development trend of current-carrying fault,a method based on heat transfer theory and least-square method was developed.First,under guidance of heat transfer theory,the temperature change of electrical equipment contact was analyzed to build the temperature model.Then,based on real-time temperature data and least-square method,parameters of temperature model was evaluated.At last,development tend forecast of current-carrying fault was realized by temperature model.The above method is verified on the basis of actual temperature data of a power station,and the result shows that the model as an exponential function can describe contacts' temperature accurately and method herein can predict the development trend of current-carrying fault precisely.
Fault Analysis And Simulation Of Ground-Fault Accident On Transformer In 500 Kv Ac/Dc Grids

Bo Zhang,Ping Lu,Jinjiao Kong,Rui Liu,Quanliang Cao,Hongbo Shao,Wanting Deng,Jun Chen

DOI: https://doi.org/10.3233/JAE-180082

2019-01-01

International Journal of Applied Electromagnetics and Mechanics

Abstract:An actual occurred ground-fault accident of 500 kV transformers in HVDC converter station is presented. A 2D transient electromagnetic-thermal-mechanical finite-element coupling model of 500 kV transformer is developed to analyze the transient process of failure, with consideration of the resistance-temperature relationship and plasticity displacement in the windings' thermal and mechanical characters. To verify the proposed finite-element model, the model is calibrated by pre-fault field test of the transformer in steady state, which shows good agreement with measurement. The short-circuit current adopted in simulation is based on actual on-site measurement of the ground-fault accident. By using the proposed model, simulation results reflect the transient process and explain the post-fault inspected damage well in term of over burn regions in thermal analysis and deformation tendency in mechanical analysis when compared with field post-fault inspection photos.
Fault tracing method for high voltage electronic current transformer during its performance test based on the FMEA

Peng Wang,Liu Jinsong,Bao Hailong

DOI: https://doi.org/10.1109/i2mtc.2018.8409693

2018-01-01

Abstract:Electronic current transformer (ECT) is a new type of high-voltage instrument transformer. It constitutes more components than that of the traditional one. To locate the fault accurately and rapidly during its performance tests, this paper proposed a fault tracing method based on the failure modes and effects analysis (FMEA). From the measuring results of the ECT under test, together with its failure patterns and the test types, we can easily locate its fault in the FMEA tables, and repair them quickly. The presented method is verified to be useful in the results of the analysis on two practical examples.
A Novel Method for Current Transformer Saturation Countermeasure Based on Comparing Two Currents' Polarities

CHEN Liyana,HE Benteng,QIAN Guoming,ZHANG Yonggang

DOI: https://doi.org/10.3321/j.issn:1000-1026.2009.08.012

2009-01-01

Abstract:A new countermeasure to current transformer (TA) saturation, namely, current polarity comparison method, for differential current protection of transmission line is proposed. It compares the polarity of the saturated current of TA and that of the differential current during internal faults and external faults with a special analysis method. EMTP simulation results show that the proposed method is able to successfully block the differential current protection during external faults even when TA saturates, and also quickly unblock it during internal faults, especially when an evolving fault occurs. © 2009 State Grid Electric Power Research Institute Press.
Saturated-core fault current limiters for AC power systems: Towards reliable, economical and better performance application

Jiaxin Yuan,Pengcheng Gan,Zhaoyang Zhang,Hang Zhou,Liangliang Wei,Kazuhiro Muramatsu

DOI: https://doi.org/10.1049/hve.2019.0049

IF: 4.967

2020-01-01

High Voltage

Abstract:With the continuous expansion of power grid capacity, the problem of short-circuit current exceeding the standard is becoming increasingly serious. Fault current limiter is a promising solution and is gradually becoming a research hotspot. In this study, fault current limiters are classified into four categories. And saturated-core fault current limiters are emphatically introduced, including its working principle and comparison with the other three categories. Saturated core fault current limiters are divided into four branches according to the ways leading the core saturated. A comprehensive review of the research activities and emerging technologies of saturated-core fault current limiters for AC power systems is presented in this study. The working principle and typical structure of DC-biased-, permanent-magnet-, superconducting- and hybrid-type saturated-core fault current limiters are introduced. The advantages and disadvantages of four types of saturated core fault current limiters are compared in detail from the aspects of current-limiting performance, iron core size and DC magnetomotive force. Real grid application examples of some types of devices are presented, as well as new progress in the techniques, are covered and discussed in detail. One may find the content of this study helpful as a detailed literature review or as practical technical guidance.
A Fault Diagnosis Method for Solid-state Fault Current Limiters Used in Three Phase Ungrounded System

Zhuxian XU,Daozhuo JIANG,Rilei LIN,Xuri LU,Shisheng CHEN

DOI: https://doi.org/10.3321/j.issn:1000-1026.2008.12.014

2008-01-01

Abstract:A fault diagnosis scheme based on the discrete Fourier transform is proposed for solid-state fault current limiters (SSFCLs) used in three phase ungrounded system. For the faults occurred on different bridge arms, the inductance current on the DC side and free-wheeling diodes current are selected as detecting parameters in the fault type diagnosis and fault locating. By transforming the time domain waveforms of detecting parameters into the frequency domain, the fault characteristics are distinguished, and the criterion is simplified, which facilitates the automatic diagnosis by computers. Simulation results indicate that the proposed scheme need minimum measurements but include complete fault information. The magnitude of each harmonic component can be used to determine the fault types, and the phase angles of the fundamental waveform to locate the faulty arms. The fault diagnosis and locating are accurate and fast.
Control Strategy and Test Study of Bi-directional Current's Solid State Fault Current Limiter

JIANG Dao-zhuo,WANG Wei,LI Dian

DOI: https://doi.org/10.3321/j.issn:1000-1026.2006.09.015

2006-01-01

Abstract:The control strategy of transformer coupling three-phase bridge type solid state fault current limiter (SSFCL) on the condition of bi-directional current is proposed and proved on a SSFCL model testing system. The test results demonstrate that the control strategy of the SSFCL ensures its satisfactory control performance and current-limiting effectiveness during its normal starting, operation or on accident current-limiting condition. The problems of the SSFCL on dual-side power system with over-long starting time and the anti-interference of its control device are analyzed. The effective countermeasures are also proposed.
Simulation Analysis of Transformer Short Circuit Fault

Yiying Li,Ying Zhang

DOI: https://doi.org/10.23977/jeeem.2023.060409

2023-01-01

Journal of Electrotechnology Electrical Engineering and Management

Abstract:: Power transformers are one of the main equipment in power production, with high cost and long manufacturing time. If a fault occurs during the power supply process, it will prevent the normal operation of the power system and result in no electricity available to power users. One of the main factors affecting the safe operation of transformers is short circuit fault, and short circuit faults at the outlet of substations or in close proximity can also pose a serious threat to transformers. This article simulates transformer short-circuit faults and establishes a simulation model using MATLAB/simulink to verify the harm caused by transformer short-circuit. Verification has shown that short circuit faults pose significant risks.
THE INFLUENCE OF CURRENT TRANSFORMER SATURATION ON BUS PROTECTION

he benteng,ma yongsheng

1998-01-01

Abstract:Until now, C. T. (Current transformer)satamtion is a important problem that affects acctale achon of Bus Proection.Ths paper studies the C. T. saturation in detail by EMTP simulation, and hased on thes draws some conclusion of C. T. saturationfoature. The saturation feature of low short cirenit connt were discussed mainly.
Research on Influence of External Current to Error of Current Transformer

张皓,赵伟,屈凯峰,江波,黄松岭,杨鹏

DOI: https://doi.org/10.19487/j.cnki.1001-8425.2008.09.007

2008-01-01

Abstract:The influence of external current to error of current transformer is analyzed and researched.
ANALYSIS AND COUNTERMEASURE FOR MISOPERATION OF LONGITUDINAL DIFFERENTIAL PROTECTION WITH UNCLEAR REASON

Wang Weijian,Li Fuying

DOI: https://doi.org/10.3321/j.issn:1000-1026.1999.18.005

1999-01-01

Abstract:Longitudinal differential protections for electric main equipments (transformer, generator, motor, busbar, etc. ) misoperate frequently under normal operation, and the same misoperation occurs over and over again. "Cause is not clear" is often the conclusion. This paper analyzes the transient performance of current transformer in the protective level. It is pointed out that TP class current transformer is too expensive for medium and low voltage device, and also difficult to install because of its bulky size. Digital optical current transducer (DOCT) has been developed successfully, which provides possibility to solve the said problems.
Fault Diagnosis Method for Neutral Grounding Three-Phase Bridge Type SSFCL

JIANG Dao-zhuo,JIN Xin,YANG Gui-yu,WU Wen-xuan,CHEN Jin-xiang

DOI: https://doi.org/10.3321/j.issn:1000-1026.2009.09.016

2009-01-01

Abstract:This paper presents a fault diagnosis method for neutral grounding three-phase bridge type solid-state fault current limiter(SSFCL).Simulation studies show that based on monitoring and analysis of current of DC reactor and two free-wheeling diodes for the bridge,different type faults of bridge-arm breaking and through can be effectively distinguished so as to implement diagnosis of bridge fault type.With current waveforms of the DC reactor and two free-wheeling diodes and their Fourier analysis,the DC,fundamental and second harmonic components can be calculated to locate fault bridge-arm.This method has many advantages,such as small monitoring amount,obviousness of fault characteristic,the simple criterion,etc.It is conducive to realize on-line monitoring and fault diagnosis for arms of rectifier bridge of SSFCL.
Review of Detection Methods for Typical Faults in Transformer Bushings*

Mu Lin,Guangning Wu,Kai Liu,Xinyu Yan,Hao Tang

DOI: https://doi.org/10.1109/mei.2024.10444768

IF: 2.939

2024-02-27

IEEE Electrical Insulation Magazine

Abstract:This article reviews the typical faults of and detection methods for transformer bushings and forecasts the future trends of transformer-bushing detection methods.

engineering, electrical & electronic

Fault Analysis and Preventive Measures of Current Transformer

Probe into a fault cause of 220kV current transformer

Research of the Coupling Transformer in the New Bridge-Type Solid State Fault Current Limiter System

Design and Realization of Power Equipment Current-carrying Faults Intelligent Warning System

Diagnostic System for Current-Carrying Fault: Modeling, Precaution, and Prediction

An online diagnosis method for the inter-turn fault of current transformer based on ΔI-E curves

Analysis on Reliability of Electronic Current Transformer Based on Failure Modes,Effects Analysis and Fault Tree Analysis

Early Warning Of Current-Carrying Faults Based On Deterioration Assessment Of Electric Contacts

Temperature Model of Electrical Equipment and Its Application in Trend Forecast for Current-Carrying Fault

Fault Analysis And Simulation Of Ground-Fault Accident On Transformer In 500 Kv Ac/Dc Grids

Fault tracing method for high voltage electronic current transformer during its performance test based on the FMEA

A Novel Method for Current Transformer Saturation Countermeasure Based on Comparing Two Currents' Polarities

Saturated-core fault current limiters for AC power systems: Towards reliable, economical and better performance application

A Fault Diagnosis Method for Solid-state Fault Current Limiters Used in Three Phase Ungrounded System

Control Strategy and Test Study of Bi-directional Current's Solid State Fault Current Limiter

Simulation Analysis of Transformer Short Circuit Fault

THE INFLUENCE OF CURRENT TRANSFORMER SATURATION ON BUS PROTECTION

Research on Influence of External Current to Error of Current Transformer

ANALYSIS AND COUNTERMEASURE FOR MISOPERATION OF LONGITUDINAL DIFFERENTIAL PROTECTION WITH UNCLEAR REASON

Fault Diagnosis Method for Neutral Grounding Three-Phase Bridge Type SSFCL

Review of Detection Methods for Typical Faults in Transformer Bushings*