Abstract:Absorptive separation for resource utilization by selective SO2 removal from flue gas is a potential method applicable in practice. A flue gas desulfurization process for SO2 utilization by selective absorption in a lab-scale absorption tower at atmospheric pressure using N-formylmorpholine (NFM) as the absorbent is developed to capture and concentrate the SO2 from flue gas, in which the CO2 content is several orders higher than that of SO2. The investigation of the effects of different operating conditions on the SO2 removal efficiency shows that the SO2 removal efficiency can be obviously enhanced by increasing NFM concentration, or decreasing the absorption temperature, the superficial gas velocity, the gas-liquid ratio, or the SO2 concentration in absorption solution. Under the optimum operating conditions (covering a temperature of 40 degrees C, a superficial gas velocity of <0.0165 m/s, a gas-liquid ratio of 200-250, a SO2 concentration in lean NFM solution of 0-10 mg/L, and a NFM concentration of 3 mol/L), the SO2 removal rate reaches over 99.5% while the absorption of CO2 is negligible. Similarly, the SO2 removal rate is as high as 99.5% obtained in consecutive absorption-desorption cycles. Desorption experiment results indicate that the absorption of sulfur dioxide is completely reversible and the release of SO(2 )from NFM is very easy and rapid at 104 degrees C. The absorption simulation result for desulfurization of flue gas vented from the industrial catalytic cracking regenerator shows that 98.0% of SO2 can be absorbed in the absorber and most of them are released in the desorber. The experimental and simulated results show that the desulfurization ability and regenerability of NFM solution is encouraging for the development of FGD process to capture the SO2 from flue gas.

FSI(furnace Sorbent Injection) Desulfurization Modeling

Numerical Simulation on Adsorbent Injection System for Mercury Removal from Coal-Fired Flue Gas

Desulfurization Characteristic of Calcium-Based Sorbent During Activation Process.

CFD Simulation of Flow Field,temperature Field and SO2 Absorption in Flue Gas Quench Tower

Sulfation Diffusion Model for SO 2 Capture on the T-T Sorbent at Moderate Temperatures

STUDY ON DESULFURIZATION CHARACTERISTIC IN CaO ACTIVATION REACTOR OF LIMESTONE INJECTION FGD SYSTEM Ⅰ--MATHEMATICS MODEL

Study On So2 Removal During Pulverized-Coal Combustion

Continuous SO2 absorption and desorption in regenerable flue gas desulfurization with ethylenediamine-phosphoric acid solution: A rate-based dynamic modeling

Modeling on circulating fluidized bed flue gas desulfurization

Kinetic Model of Cao/Fly Ash Sorbent for Flue Gas Desulphurization at Moderate Temperatures

D306 EXPERIMENTS AND MATHEMATICAL MODEL ON FLUE GAS DESULFURIZATION OF CIRCULATING FLUIDIZED BED

Numerical and Experimental Investigation of the Effects of Impinging Streams to Enhance Ca-based Sorbent Capture of SO2

STUDY ON DESULFURIZATION CHARACTERISTIC IN CaO ACTIVATION REACTOR OF LIMESTONE INJECTION FGD SYSTEM --EXPERIMENTAL RESULTS AND DISCUSSION

Study on Flue Gas Desulfurization Process with Selective SO2 Removal by N-formylmorpholine

Modeling of the Flue Gas Desulfurization in a CFB Riser Using the Eulerian Approach with Heterogeneous Drag Coefficient

Distributed pore model for sulfation of calcium-based sorbent

Experimental Study on Desulfurization Characteristics of Dry Sorbent Injection at Low SO2 Concentrations

Experimental and model investigation on the mass balance of a dry circulating fluidized bed for flue gas desulfurization system

Effect of Solids Concentration Distribution on the Flue Gas Desulfurization Process

Integrated Modeling of Semi-dry Flue Gas Desulfurization

PORE SIZE DISTRIBUTION MODEL FOR SULFATION OF CALCIUM-BASED SORBENT