Fully Etched Grating Coupler Diplexer for Integrated WDM PON Transceivers

Lirong Cheng,Simei Mao,Xin Mu,Sailong Wu,H. Y. Fu

DOI: https://doi.org/10.1364/cleopr.2020.p2_3

2020-01-01

Abstract:We propose and design a grating coupler diplexer for dual-wavelength-band coupling and splitting for low-cost WDM PON transceivers. Insertion losses are 3.2 dB and 3.5 dB for upstream and downstream channels respectively.

What problem does this paper attempt to address?

Three-Port Dual-Wavelength-Band Grating Coupler for WDM-PON Applications

Lirong Cheng,Simei Mao,Caiyue Zhao,Xin Tu,Qian Li,H. Y. Fu

DOI: https://doi.org/10.1109/lpt.2021.3049270

IF: 2.6

2021-01-01

IEEE Photonics Technology Letters

Abstract:Grating coupling is a widely adopted strategy for coupling light into optical waveguides. While this versatile approach benefits both fabrication and alignment, grating couplers are particularly sensitive to both wavelength and polarization. These drawbacks hinder its application in integrated wavelength-division-multiplexing passive optical network (WDM-PON) transceivers, where widely separated wavelength bands are utilized for upstream and downstream signals. In this letter, we propose a three-port grating coupler that enables polarization-independent receiving for the downstream signal from fiber and single-polarized coupling of the upstream signal from chip. Dual-wavelength-band operation is obtained by adding an output port to couple upstream wavelength on existing polarization-splitting grating coupler for downstream wavelength. Peak coupling efficiencies of -2.93 dB and -3.50 dB are achieved for 1266 nm and 1481 nm respectively. This grating coupler design can be adopted in transceivers for fiber-to-the-home (FTTH) networks.
A Nonreciprocal Add-Drop Multiplexer Based on Grating Assisted Couplers

Huiye Qiu,Ting Hu,Ping Yu,Ying Wang,Xiaoqing Jiang

DOI: https://doi.org/10.1016/j.ijleo.2015.07.195

IF: 3.1

2015-01-01

Optik

Abstract:We propose a nonreciprocal optical add-drop multiplexer with silicon waveguide, which is realized by grating assisted coupler employing magneto-optical nonceciprocal phase shift. This device can achieve different adding or dropping peak wavelengths when light is launched in the forward-directed and backward-directed propagation. The calculation results show that the shift of the different dropping peak wavelengths is up to 0.7nm. Also, we demonstrate its applications for narrowband optical isolators and circulators. This work demonstrates that on-chip nonreciprocal optical add-drop multiplexers and optical isolations can be implemented with the proposed device, which has promising applications for optical communication systems and photonic integrated devices.
Monolithically Integrated Fiber-to-the-home Diplexers and Triplexers Using a Bilevel Etched 2×2 Optical Coupler

Li Zhang,Lei Wang,Jian-Jun He

DOI: https://doi.org/10.1364/ao.48.000f44

IF: 1.9

2009-01-01

Applied Optics

Abstract:A novel design of monolithically integrated diplexers and triplexers for fiber-to-the-home applications is presented. A bilevel etched asymmetrical 2 x 2 optical coupler is analyzed for efficient couplings of both upstream and downstream signals. The design of the diplexer is extended to a triplexer by adding an etched diffraction grating as an additional downstream demultiplexing element. The total size of the integrated diplexer and triplexer is smaller than 500 microm x 500 microm.
Monolithically integrated FTTH diplexer using bi-level etched 2×2 optical coupler

Li Zhang,Lei Wang,Jian-Jun He

DOI: https://doi.org/10.1364/aoe.2008.sak41

2008-01-01

Abstract:A novel design of monolithically integrated diplexers for FTTH applications is presented. A bi-level etched asymmetrical 2times2 optical coupler is analyzed for efficient couplings of both upstream and downstream signals.
Fiber-Chip Bi-Wavelength Multiplexing with Subwavelength Single-Etch Grating Coupler and Diplexer

Lirong Cheng,Simei Mao,Yinghui Wang,H. Y. Fu

DOI: https://doi.org/10.1109/jphot.2022.3143689

IF: 2.4

2022-01-01

IEEE Photonics Journal

Abstract:We propose a silicon photonicgrating coupling scheme for dual-band multiplexing in optical fibers. By utilizing subwavelength grating effective refractive index engineering, a dual-band operating grating coupler and a wavelength-polarization diplexer are designed. Both devices are fabricated on a 220-nm silicon-on-insulator and require only one 220-nm full etch step to facilitate cost-effective production. The subwavelength grating coupler guides S-band and O-band lights from a single-mode fiber into a waveguide as transverse-electric and transverse-magnetic modes, while the subwavelength diplexer separates the two signals into two waveguides. Experimentally, our proposed scheme for coupling and multiplexing can achieve a total insertion loss of –4.26 dB at near 1490 nm and –5.86 dB at near 1310 nm.
High-efficiency Grating Coupler Based on Fast Directional Optimization and Robust Layout Strategy in 130 Nm CMOS Process.

Xiangyu Luo,Guangcan Mi,Yanbo Li,Tao Chu

DOI: https://doi.org/10.1364/ol.452054

IF: 3.6

2022-01-01

Optics Letters

Abstract:We experimentally demonstrated a high-efficiency grating coupler by combining an interleaved etch and apodized structure for fiber-to-chip coupling. The grating coupler was optimized using the fast directional optimization method to achieve apodization. The grating coupler utilized a layout strategy involving an extended mask to avoid alignment errors for a multi-etch structure. The coupling efficiency was measured to be -2.2 dB at a wavelength of 1549 nm with a 3 dB bandwidth of 47 nm. The grating coupler, having no gold reflector, subwavelength index matching structure, or additional material layers, was fabricated using a commercial silicon photonics process with a minimum feature size of 140 nm. This grating coupler design provides a robust and effective coupling scheme and the proposed method can be employed to adopt the design in accordance with standard foundry design rules.
Etched-Diffraction-Grating-Based Planar Waveguide Demultiplexer on Silicon-on-Insulator

Wenhui Wang,Yanzhe Tang,Yunxiang Wang,Hongchang Qu,Yaming Wu,Tie Li,Jianyi Yang,Yuelin Wang,Ming Liu

DOI: https://doi.org/10.1023/B:OQEL.0000025795.18597.c8

IF: 3

2004-01-01

Optical and Quantum Electronics

Abstract:An optical wavelength demultiplexer with the etched diffraction grating (EDG) on the silicon-on-insulator (SOI) material is demonstrated. Fabricated by the wet-anisotropic-etching method, 90° turning mirrors are used to bend waveguides, and the size of the EDG-based demultiplexer is minimized to only 16×2.5 mm 2 . The crosstalk is below −16 dB. The on-chip loss is about 9.97 dB, which is composed of about 8.72 dB excess loss and 1.25 dB diffraction loss. The polarization-dependent central wavelength shift is below 0.13 nm, and the polarization-dependent loss is about 0.35 dB. The sources of the crosstalk and loss are discussed in details, and the related measures to improve the performance are also presented.
High-Efficiency Dual-Band-Multiplexing Three-Port Grating Coupler On 220-Nm Silicon-On-Insulator With 248-Nm Deep-Uv Lithography

Lirong Cheng,Simei Mao,Zhi Li,Xin Tu,H Y Fu

DOI: https://doi.org/10.1364/OL.430807

IF: 3.6

2021-01-01

Optics Letters

Abstract:We experimentally demonstrate a novel, to the best of our knowledge, three-port grating coupler (TPGC) for dual-wavelength-band operation. The TPGC can couple light to/from two ports for S/C-band with polarization diversity and a third port for O-band. Such a coupling scheme could be applied in an integrated wavelength-division-multiplexing passive optical network (PON) unit, benefiting a polarization-diverse receiver for downstream S/C-band and transmitter for upstream O-band. The device is fabricated on a multi-project wafer, with peak coupling efficiency measured to be -3.8 dB and -5.4 dB for O-band. and S/C-band, respectively. We also present a proof-ofconcept demonstration for 10-Gb/s PON transmission based on the TPGC. (C) 2021 Optical Society of America
High Efficiency Grating Coupler for Coupling Between Single-Mode Fiber and SOI Waveguides

Zhang Can,Sun Jing-Hua,Xiao Xi,Sun Wei-Min,Zhang Xiao-Jun,Chu Tao,Yu Jin-Zhong,Yu

DOI: https://doi.org/10.1088/0256-307x/30/1/014207

2013-01-01

Chinese Physics Letters

Abstract:A high efficiency grating coupler between single-mode fiber and silicon-on-insulator waveguide is designed by a formula method. Over 78.5% coupling efficiency (>−1.05 dB) with 3 dB bandwidth about 50 nm for one grating coupler is obtained experimentally and this result is the highest one as far as we know. This grating coupler is CMOS compatible which needs only one etch-step and is designed for a standard SOI chip without any Bragg reflector or bottom reflector.
High-Efficiency Unidirectional Dual-Wavelength-Band Grating Coupler with 1D Subwavelength Structure

Haoyang Tan,Baobao Chen,Yi Zhao,Shiming Gao,Xiaowei Guan

DOI: https://doi.org/10.1109/lpt.2023.3326185

IF: 2.6

2023-01-01

IEEE Photonics Technology Letters

Abstract:A unidirectional dual-wavelength-band grating coupler with one-dimensional (1D) subwavelength structures is proposed and experimentally demonstrated. Inverse optimization method is used for the design and the grating coupler fabricated on the silicon-on-insulator chip can achieve efficient fiber-chip coupling simultaneously in the O-band and the L-band. The peak coupling efficiencies in the two bands are measured to be 19.7% and 19.5% with 3-dB bandwidths of 27 and 38-nm, respectively.
High-efficiency Wideband SiNx-on-SOI Grating Coupler with Low Fabrication Complexity.

Pengfei Xu,Yanfeng Zhang,Zengkai Shao,Lin Liu,Lidan Zhou,Chunchuan Yang,Yujie Chen,Siyuan Yu

DOI: https://doi.org/10.1364/ol.42.003391

IF: 3.6

2017-01-01

Optics Letters

Abstract:The chip-fiber grating coupler is a fundamental building block in integrated photonics, providing convenient on-wafer testing and packaging. Couplers based on a silicon nitride (SiNx) material platform can achieve wider bandwidths than silicon-based couplers, but suffer from lower efficiency due to the relative low material refractive index. The efficiency of the SiNx grating coupler can be improved by using high-reflectivity silicon grating reflectors underneath. However, such a silicon grating reflector requires several fabrication steps, including lithography, etching, high precision alignment (HPA), and chemical mechanical polishing (CMP). In this Letter, we demonstrate an easy-to-fabricate SiNx-on-SOI transverse-electric mode grating coupler requiring only one patterning step (grating alone), and without the need for HPA and CMP. A coupling coefficient of -2.5 dB and 1-dB-bandwidth of 65 nm has been experimentally measured.
Dual-Wavelength-Band Multiplexed Grating Coupler on Multilayer SiN-on-SOI Photonic Integrated Platform

Lirong Cheng,Simei Mao,Xin Mu,Sailong Wu,H. Y. Fu

DOI: https://doi.org/10.1364/cleo_at.2020.jth2f.8

2020-01-01

Abstract:We propose and design a dual-layer grating coupler for dual-wavelength-band multiplexing on multilayer SiN-on-SOI photonic integrated platform. Its peak coupling efficiencies are -2.95 dB for O-band and -2.49 dB for C-band.
Design and Fabrication of An 8×500GHz InP-Based EchelleGrating Wavelength Multiplexer

Ge Mu,Lin Wu,Jian-Jun He

DOI: https://doi.org/10.1364/acpc.2014.ath1a.1

2014-01-01

Abstract:We present an 8×500GHz echelle grating multiplexer on InGaAsP/InP platform in 1550nm wavelength band. The device insertion loss of the device is 8.2dB and the adjacent channel crosstalk ranges from 20dB to 25dB.
An Eight-Channel 400 GHz-Spacing Etched Diffraction Grating Multi/Demultiplexer on a Nanophotonic Silicon-on-Insulator Platform

shen ao,qiu chen,hu ting,xu chao,jiang xiaoqing,li yubo,yang jianyi

DOI: https://doi.org/10.1088/0256-307X/30/8/084204

2013-01-01

Chinese Physics Letters

Abstract:An eight-channel 400 GHz-spacing planar waveguide multi/demultiplexer employing etched diffraction grating is designed and fabricated on a silicon-on-insulator platform with a 220 nm thick top layer. The design parameters are optimized by scalar diffraction simulation to obtain optimal performance with a small footprint of only 0.75 mm(2). A bi-level adiabatic taper is used to connect the input/output waveguide and the slab waveguide so as to reduce the insertion loss and the broadening of the diffraction angle of the propagating light. The device is fabricated in a two-step process with E-beam lithography and dry etching, and the alignment accuracy is 10 nm or even better. Measurements show that the insertion loss is 7.35 dB and the crosstalk between adjacent channels is about -15 dB. Ways to improve the performance are also investigated in detail.
InP Based Echelle Diffraction Grating Multiplexer with Flat-Passband

Lili Le,Yayan Chu,Zhipeng Hu,Jinyan Song,Jian-Jun He

DOI: https://doi.org/10.1109/icocn.2017.8121401

2017-01-01

Abstract:An echelle diffraction grating (de)multiplexer with arc shaped grating teeth, based on a multi-guide vertical integration platform in InP is presented. The device can be applied to the 100GBASE-LR4 Ethernet systems, the crosstalk is better than -19 dB. By adjusting grating facets, the 3-dB spectral bandwidth is increased to 2.2 nm compared with 1.7 nm in a conventional design with a loss penalty less than 2 dB. And the nonuniformity is reduced form 1.7 dB to 0.68 dB.
Dual-layer SiNx-on-SOI Grating Coupler As an Efficient Higher-Order Fiber Mode Multiplexer

Lirong Cheng,Simei Mao,Yixiang Hu,H. Y. Fu

DOI: https://doi.org/10.1364/cleo_at.2021.jw1a.178

2021-01-01

Abstract:We demonstrate a dual-layer grating coupler as an efficient higher-order fiber mode multiplexer. Four channels from a fiber array can be multiplexed into four distinct TE-polarized modes in a few-mode fiber using the proposed multiplexer.
Compact Five-mode De-multiplexer based on Grating Assisted Asymmetric Directional Couplers

Simei Mao,Lirong Cheng,Sailong Wu,Xin Mu,Xin Tu,Qian Li,H.Y. Fu

DOI: https://doi.org/10.1364/acpc.2020.m4a.128

2020-01-01

Abstract:We propose a 25-μm five-mode de-multiplexer based on subwavelength grating directional couplers with constant bus waveguide. The insertion loss is less than 0.31 dB at 1550 nm and its 1-dB bandwidth is over 100 nm.
Low-loss Grating Coupler with a Gradient Index-Matching Subwavelength Structure

Xiangyu Luo,Weijie Tang,Tao Chu

DOI: https://doi.org/10.1016/j.optlastec.2023.109860

2024-01-01

Abstract:O-band high-efficiency grating couplers were designed, and experimentally demonstrated with novel gradient index-matching subwavelength structures to reduce the leakage loss and mode mismatch. Trapezoidal subwavelength gratings and apodization were implemented to realize the change in the gradual effective index guided by the effective medium theory and improve the coupling efficiency. The grating couplers were fabricated with a simple single-step etching process. The measured lowest coupling losses of conventional rectangular and trapezoidal SWG grating couplers were -1.93 dB and -1.72 dB in the O-band, respectively. The latter result is the lowest reported losses of single-step etched grating couplers in the O-band with a minimum feature size of 120 nm, which is the typical minimum feature size in 130 nm CMOS node commercial silicon photonic processes.
Monolithic Integrated Wavelength Demultiplexer Based on a Waveguide Rowland Circle Grating in InGaAsP/lnP

JJ He,B Lamontagne,A Delage,L Erickson,M Davies,ES Koteles

DOI: https://doi.org/10.1109/50.664075

IF: 4.7

1998-01-01

Journal of Lightwave Technology

Abstract:We present detailed modeling and experimental results for an improved design of an InGaAsP/lnP wavelength demultiplexer based on a monolithically integrated Rowland circle grating. The design incorporated ten wavelength channels at 1.55 mu m with a uniform spacing of 2 nm. The total on-chip loss was about 10 dB and the crosstalk between adjacent channels was as low as -25 dB. It was shown that low-loss etched turning mirrors can reduce the total on-chip loss by about 4 dB compared to traditional 90 degrees curved multimode waveguides. By replacing standard hat grating facets with retro-reflecting V-shaped facets in the echelle grating, the loss was further reduced by 4 dB, Polarization independent operation within a passband of 0.5 nm was achieved by using multimode output waveguide, The potential sources producing the crosstalk have been analyzed and fabrication modifications for further improvement are suggested.
Efficient Fiber-To-Slot-Waveguide Grating Couplers Based on A Double-Strip Waveguide

Fei Li,Xiaowen Sun,Jiayang Wu,Xiaofeng Hu,Linjie Zhou,Yikai Su

DOI: https://doi.org/10.1109/lpt.2013.2286861

IF: 2.6

2013-01-01

IEEE Photonics Technology Letters

Abstract:We propose and experimentally demonstrate a fiber-to-slot-waveguide grating coupler based on a double-strip waveguide, together with a double-strip-to-slot waveguide mode converter. By employing the double-strip waveguide, we improve the coupling efficiency from a fiber to the slot waveguide by similar to 1.2 dB, compared with previous grating-based two-stage schemes. In addition, the double-strip-to-slot waveguide mode converter, consisting of two S bends and a taper pair, occupies a short conversion length of only 4 mu m. Parameters, including taper length and S-bend length are numerically optimized. Bandwidth and fabrication error tolerance are also analyzed. Experimental results verify the feasibility of the proposed scheme.

Fully Etched Grating Coupler Diplexer for Integrated WDM PON Transceivers

Three-Port Dual-Wavelength-Band Grating Coupler for WDM-PON Applications

A Nonreciprocal Add-Drop Multiplexer Based on Grating Assisted Couplers

Monolithically Integrated Fiber-to-the-home Diplexers and Triplexers Using a Bilevel Etched 2×2 Optical Coupler

Monolithically integrated FTTH diplexer using bi-level etched 2×2 optical coupler

Fiber-Chip Bi-Wavelength Multiplexing with Subwavelength Single-Etch Grating Coupler and Diplexer

High-efficiency Grating Coupler Based on Fast Directional Optimization and Robust Layout Strategy in 130 Nm CMOS Process.

Etched-Diffraction-Grating-Based Planar Waveguide Demultiplexer on Silicon-on-Insulator

High-Efficiency Dual-Band-Multiplexing Three-Port Grating Coupler On 220-Nm Silicon-On-Insulator With 248-Nm Deep-Uv Lithography

High Efficiency Grating Coupler for Coupling Between Single-Mode Fiber and SOI Waveguides

High-Efficiency Unidirectional Dual-Wavelength-Band Grating Coupler with 1D Subwavelength Structure

High-efficiency Wideband SiNx-on-SOI Grating Coupler with Low Fabrication Complexity.

Dual-Wavelength-Band Multiplexed Grating Coupler on Multilayer SiN-on-SOI Photonic Integrated Platform

Design and Fabrication of An 8×500GHz InP-Based EchelleGrating Wavelength Multiplexer

An Eight-Channel 400 GHz-Spacing Etched Diffraction Grating Multi/Demultiplexer on a Nanophotonic Silicon-on-Insulator Platform

InP Based Echelle Diffraction Grating Multiplexer with Flat-Passband

Dual-layer SiNx-on-SOI Grating Coupler As an Efficient Higher-Order Fiber Mode Multiplexer

Compact Five-mode De-multiplexer based on Grating Assisted Asymmetric Directional Couplers

Low-loss Grating Coupler with a Gradient Index-Matching Subwavelength Structure

Monolithic Integrated Wavelength Demultiplexer Based on a Waveguide Rowland Circle Grating in InGaAsP/lnP

Efficient Fiber-To-Slot-Waveguide Grating Couplers Based on A Double-Strip Waveguide