Dual-layer SiNx-on-SOI Grating Coupler As an Efficient Higher-Order Fiber Mode Multiplexer

Lirong Cheng,Simei Mao,Yixiang Hu,H. Y. Fu

DOI: https://doi.org/10.1364/cleo_at.2021.jw1a.178

2021-01-01

Abstract:We demonstrate a dual-layer grating coupler as an efficient higher-order fiber mode multiplexer. Four channels from a fiber array can be multiplexed into four distinct TE-polarized modes in a few-mode fiber using the proposed multiplexer.

What problem does this paper attempt to address?

Design and Numerical Optimization of A Mode Multiplexer Based on Few-Mode Fiber Couplers

Yiwei Xie,Songnian Fu,Hai Liu,Hailiang Zhang,Ming Tang,P. Shum,Deming Liu

DOI: https://doi.org/10.1088/2040-8978/15/12/125404

IF: 2.1

2013-01-01

Journal of Optics

Abstract:Mode division multiplexing (MDM) transmission based on few-mode fibers (FMFs) appears to be an alternative solution for overcoming the capacity limit of single-mode fibers (SMFs). A FMF coupler-based mode division multiplexer/demultiplexer (MMUX/DeMMUX) is proposed and theoretically investigated after the fabricated FMF is characterized. MMUXs/DeMMUXs with a mode contrast ratio (MCR) of more than 20 dB can be obtained for two-mode multiplexing and three-mode multiplexing over a wavelength span of 60 and 10 nm, respectively. We numerically verify the proposed MMUX/DeMMUX which has the advantages of high MCR, easy fabrication and maintenance, and low wavelength dependence.
A Nonreciprocal Add-Drop Multiplexer Based on Grating Assisted Couplers

Huiye Qiu,Ting Hu,Ping Yu,Ying Wang,Xiaoqing Jiang

DOI: https://doi.org/10.1016/j.ijleo.2015.07.195

IF: 3.1

2015-01-01

Optik

Abstract:We propose a nonreciprocal optical add-drop multiplexer with silicon waveguide, which is realized by grating assisted coupler employing magneto-optical nonceciprocal phase shift. This device can achieve different adding or dropping peak wavelengths when light is launched in the forward-directed and backward-directed propagation. The calculation results show that the shift of the different dropping peak wavelengths is up to 0.7nm. Also, we demonstrate its applications for narrowband optical isolators and circulators. This work demonstrates that on-chip nonreciprocal optical add-drop multiplexers and optical isolations can be implemented with the proposed device, which has promising applications for optical communication systems and photonic integrated devices.
Optimization of Few-Mode-Fiber Based Mode Converter for Mode Division Multiplexing Transmission

Yiwei Xie,Songnian Fu,Minming Zhang,M. Tang,P. Shum,Deming Liu

DOI: https://doi.org/10.1016/j.optcom.2013.05.016

IF: 2.4

2013-01-01

Optics Communications

Abstract:Few-mode-fiber (FMF) based mode division multiplexing (MDM) is a promising technique to further increase the transmission capacity of single mode fibers. We propose and numerically investigate a fiber-optical mode converter (MC) using long period gratings (LPGs) fabricated on the FMF by point-by-point CO2 laser inscription technique. In order to precisely excite three modes (LP01, LP11, and LP02), both untilted LPG and tilted LPG are comprehensively optimized through the length, index modulation depth, and tilt angle of the LPG in order to achieve a mode contrast ratio (MCR) of more than 20dB with less wavelength dependence. It is found that the proposed MCs have obvious advantages of high MCR, low mode crosstalk, easy fabrication and maintenance, and compact size.
Fiber-Chip Bi-Wavelength Multiplexing with Subwavelength Single-Etch Grating Coupler and Diplexer

Lirong Cheng,Simei Mao,Yinghui Wang,H. Y. Fu

DOI: https://doi.org/10.1109/jphot.2022.3143689

IF: 2.4

2022-01-01

IEEE Photonics Journal

Abstract:We propose a silicon photonicgrating coupling scheme for dual-band multiplexing in optical fibers. By utilizing subwavelength grating effective refractive index engineering, a dual-band operating grating coupler and a wavelength-polarization diplexer are designed. Both devices are fabricated on a 220-nm silicon-on-insulator and require only one 220-nm full etch step to facilitate cost-effective production. The subwavelength grating coupler guides S-band and O-band lights from a single-mode fiber into a waveguide as transverse-electric and transverse-magnetic modes, while the subwavelength diplexer separates the two signals into two waveguides. Experimentally, our proposed scheme for coupling and multiplexing can achieve a total insertion loss of –4.26 dB at near 1490 nm and –5.86 dB at near 1310 nm.
Silicon-on-Insulator Mode (de)multiplexer for On-Chip Mode-Division Multiplexing

Huiye Qiu,Hui Yu,Yongheng Jin,Yuehai Wang,Xiaoqing Jiang

DOI: https://doi.org/10.1364/acp.2013.af1a.2

2013-01-01

Abstract:We propose a simple 1×4 silicon mode (de)multiplexer based on multimode grating-assisted-couplers. Due to the contra-directional coupling, precise control of the coupling strength and the coupling length are not needed.
Silicon Mode Multi/Demultiplexer Based on Multimode Grating-Assisted Couplers

Huiye Qiu,Hui Yu,Ting Hu,Guomin Jiang,Haifeng Shao,Ping Yu,Jianyi Yang,Xiaoqing Jiang

DOI: https://doi.org/10.1364/oe.21.017904

IF: 3.8

2013-01-01

Optics Express

Abstract:A simple and low-crosstalk 1 × 4 silicon mode (de)multiplexer based on multimode grating-assisted-couplers is proposed. Mode transitions can be flexibly controlled by designing the grating period at the phase-matching condition. Due to the contra-directional coupling, precise control of the coupling strength and the coupling length are not needed in the system. Calculation results show that the insertion loss and the 3 dB bandwidths of the device are 0.2 dB and 3.7 nm, 0.34 dB and 7.6 nm, and 0.21 dB and 11.8 nm for the channels which (de)multiplex to the 1st, 2nd, and 3rd modes of the bus waveguide, respectively.
On-chip mode multiplexer based on a single grating coupler

yunhong ding,haiyan ou,jing xu,meng xiong,christophe peucheret

DOI: https://doi.org/10.1109/IPCon.2012.6358818

2012-01-01

Abstract:A two-mode multiplexer based on a single grating coupler is proposed and demonstrated on a silicon chip. The LP01 and LP11 modes of a few-mode fiber are excited from TE0 and TE1 silicon waveguide modes.
Dual-Wavelength-Band Multiplexed Grating Coupler on Multilayer SiN-on-SOI Photonic Integrated Platform

Lirong Cheng,Simei Mao,Xin Mu,Sailong Wu,H. Y. Fu

DOI: https://doi.org/10.1364/cleo_at.2020.jth2f.8

2020-01-01

Abstract:We propose and design a dual-layer grating coupler for dual-wavelength-band multiplexing on multilayer SiN-on-SOI photonic integrated platform. Its peak coupling efficiencies are -2.95 dB for O-band and -2.49 dB for C-band.
High-efficiency Grating Coupler Based on Fast Directional Optimization and Robust Layout Strategy in 130 Nm CMOS Process.

Xiangyu Luo,Guangcan Mi,Yanbo Li,Tao Chu

DOI: https://doi.org/10.1364/ol.452054

IF: 3.6

2022-01-01

Optics Letters

Abstract:We experimentally demonstrated a high-efficiency grating coupler by combining an interleaved etch and apodized structure for fiber-to-chip coupling. The grating coupler was optimized using the fast directional optimization method to achieve apodization. The grating coupler utilized a layout strategy involving an extended mask to avoid alignment errors for a multi-etch structure. The coupling efficiency was measured to be -2.2 dB at a wavelength of 1549 nm with a 3 dB bandwidth of 47 nm. The grating coupler, having no gold reflector, subwavelength index matching structure, or additional material layers, was fabricated using a commercial silicon photonics process with a minimum feature size of 140 nm. This grating coupler design provides a robust and effective coupling scheme and the proposed method can be employed to adopt the design in accordance with standard foundry design rules.
Three-mode All-Optical (de)multiplexing on a SOI Chip

Yan-Si Le,Zhi Wang,Zhi-Yong Li,Ying Li,Qiang Li,Can Cui,Chong-Qing Wu

DOI: https://doi.org/10.1016/j.optcom.2017.04.059

IF: 2.4

2018-01-01

Optics Communications

Abstract:An on-chip three-mode division multiplexing circuit using a simple ADC-based TE 0 & TE 1 & TE 2 (de)multiplexer is demonstrated to improve the link capacity of on-chip optical interconnects. The proposed (de)multiplexer does not contain any tapered waveguide which is different from the previous mode (de)multiplexer based on ADCs. Here, we choose multimode waveguide width first and then confirm corresponding width of the other two waveguides. Thus the bus waveguide without any tapers can not only reduce complexity of (de)multiplexer but also reduce difficulty of the fabrication. Our simulation results show that the hybrid multiplexer has relatively low loss and low crosstalk about −40 dB, −26.99 dB and −28.72 dB for each mode around 1550 nm with a width-variation w =±25 nm. These properties make the proposed mode-(de)multiplexer suitable for application in high-capacity data transmission.
High-efficiency Wideband SiNx-on-SOI Grating Coupler with Low Fabrication Complexity.

Pengfei Xu,Yanfeng Zhang,Zengkai Shao,Lin Liu,Lidan Zhou,Chunchuan Yang,Yujie Chen,Siyuan Yu

DOI: https://doi.org/10.1364/ol.42.003391

IF: 3.6

2017-01-01

Optics Letters

Abstract:The chip-fiber grating coupler is a fundamental building block in integrated photonics, providing convenient on-wafer testing and packaging. Couplers based on a silicon nitride (SiNx) material platform can achieve wider bandwidths than silicon-based couplers, but suffer from lower efficiency due to the relative low material refractive index. The efficiency of the SiNx grating coupler can be improved by using high-reflectivity silicon grating reflectors underneath. However, such a silicon grating reflector requires several fabrication steps, including lithography, etching, high precision alignment (HPA), and chemical mechanical polishing (CMP). In this Letter, we demonstrate an easy-to-fabricate SiNx-on-SOI transverse-electric mode grating coupler requiring only one patterning step (grating alone), and without the need for HPA and CMP. A coupling coefficient of -2.5 dB and 1-dB-bandwidth of 65 nm has been experimentally measured.
Silicon Photonic Integrated Circuit Mode Multiplexer

Yunhong Ding,Haiyan Ou,Jing Xu,Christophe Peucheret

DOI: https://doi.org/10.1109/LPT.2013.2247394

IF: 2.6

2013-01-01

IEEE Photonics Technology Letters

Abstract:We propose and demonstrate a novel silicon photonic integrated circuit enabling multiplexing of orthogonal modes in a few-mode fiber (FMF). By selectively launching light to four vertical grating couplers, all six orthogonal spatial and polarization modes supported by the FMF are successfully excited independently.
High Efficiency Grating Coupler for Coupling Between Single-Mode Fiber and SOI Waveguides

Zhang Can,Sun Jing-Hua,Xiao Xi,Sun Wei-Min,Zhang Xiao-Jun,Chu Tao,Yu Jin-Zhong,Yu

DOI: https://doi.org/10.1088/0256-307x/30/1/014207

2013-01-01

Chinese Physics Letters

Abstract:A high efficiency grating coupler between single-mode fiber and silicon-on-insulator waveguide is designed by a formula method. Over 78.5% coupling efficiency (>−1.05 dB) with 3 dB bandwidth about 50 nm for one grating coupler is obtained experimentally and this result is the highest one as far as we know. This grating coupler is CMOS compatible which needs only one etch-step and is designed for a standard SOI chip without any Bragg reflector or bottom reflector.
A segment-coupled six-mode multiplexer based on multi-core fiber

Menglei Pei,Jianshe Li,Shuguang Li,Yuxin Ding,Xiaokai Wang,Zenghui Li,Chun Wang,Chengjun Wang,Xingwei Li,Geng Li,Yuanyuan Zhao

DOI: https://doi.org/10.1016/j.infrared.2024.105147

IF: 2.997

2024-01-10

Infrared Physics & Technology

Abstract:In this paper, a segment-coupled six-mode multiplexer based on multi-core fiber (MCF) is proposed to achieve multiplexing of LP 01 , LP 11 , LP 21 , LP 02 , LP 31 and LP 12 modes according to the principle of mode coupling and phase matching. The mode multiplexer consists of a two-part fiber waveguide that supports six modes of transmission at 1.55 μm wavelength. The transmission performance is analyzed with the finite element method (FEM) and the beam propagation method (BPM). The simulation results show that the insertion loss (IL) of the mode multiplexer is less than 1 dB in the wavelength range of 1.5439–1.5558 μm, and the lowest IL is 0.1837 dB. The coupling efficiencies (CEs) of the six modes are 99.7 %, 92.0 %, 98.6 %, 98.3 %, 97.4 % and 86.6 %, respectively. The designed mode multiplexer dramatically improves fiber space utilization while achieving more higher-order mode conversion. The mode multiplexer can be applied to the mode division multiplexing (MDM) system to solve the problem of mode multiplexing and demultiplexing.

optics,physics, applied,instruments & instrumentation
Novel Wavelength Multiplexer Using (<italic>N</italic> + 1) × (<italic>N</italic> + 1) Arrayed Waveguide Grating and Polarization-Combiner-Rotator on SOI Platform

Jun Zou,Xiao Ma,Xiang Xia,Changhui Wang,Ming Zhang,Jinhua Hu,Xuyang Wang,Jian-Jun He

DOI: https://doi.org/10.1109/JLT.2021.3053837

IF: 4.7

2021-01-01

Journal of Lightwave Technology

Abstract:We propose an ultra-compact novel wavelength multiplexer employing a (N + 1) × (N + 1) arrayed waveguide grating (AWG) and a polarization-combiner-rotator (PCR) on the SOI platform, to realize a multiplexing for 2N wavelengths with a spacing of Δλ. The (N + 1) × (N + 1) AWG works at a bidirectional way to provide two groups of N × 1 wavelength multiplexing with each group having a channel spacing of 2×Δλ, and the central wavelengths of all input channels in one group have a wavelength shift of Δλ with respect to those in the other group. The double channel spacing results in a significant decrease on the footprint of the (N + 1) × (N + 1) AWG-based multiplexer compared with a conventional 2N × 1 AWG multiplexer with the same wavelength spacing Δλ. Due to the fact that a single mode fiber is insensitive to the polarization of input light, if we consider short reach datacom applications such as 100/400 GbE, the two separate multiplexing outputs of the (N + 1) × (N + 1) AWG can be combined as one output with one half wavelengths working at TE polarization and the other at TM polarization by employing a low loss and broadband PCR. In the experiment, we demonstrate a 16 × 200 GHz multiplexer based on a 9 × 9 AWG. The experimental results show that the on-chip loss of the fabricated multiplexer is 2.7 dB and the loss uniformity is 0.5 dB. The 1-dB and 3-dB bandwidths are >0.56 nm (i.e., 35% of the wavelength spacing) and >1.1 nm (i.e., 69% of the wavelength spacing), respectively. They can also be further increased by decreasing the gap between adjacent input waveguides at the interfaces of star couplers of the designed AWG without inducing an excess loss. The proposed multiplexer has great potential for application to future super large capacity (> Tb/s) data transmission systems.
Silicon Two-Mode Multi/demultiplexer Based on Tapered Couplers

Haiqin Li,Shiqi Li,Tianjun Yang,Jiayun Xu,Jun Li,Weiwei Chen,Pengjun Wang,Tingge Dai,Gencheng Wang,Jianyi Yang

DOI: https://doi.org/10.1016/j.ijleo.2018.09.115

IF: 3.1

2018-01-01

Optik

Abstract:In this paper, a two-mode (de)multiplexer utilizing the coupling between tapered waveguides and a wide multimode waveguide is designed and experimentally demonstrated. The tapered waveguides are composed of a reverse-tapered waveguide and a narrow tapered waveguide. The proposed mode (de)multiplexer is fabricated on silicon-on-insulator (SOI) wafer in a commercial 0.18-mu m CMOS-compatible process. The qualitative functionality of the device is mainly determined by the width of the large end of the reverse-tapered waveguide. Experimental results show that the demultiplexing crosstalk of a pair of tapered-coupler-based two-mode (de)multiplexers is lower than -13.5 dB within a bandwidth from 1528 nm to 1570 nm and less than -16.6 dB from 1540 nm to 1560 nm.
Low-Loss All-Fiber Mode Multiplexers for Weakly-Coupled 4-Mode Fiber

Ruichun Wang,Ying Li,Tingting Dong,Jie Luo,Dai Lu,Liubo Yang,Jun Chu,Lei Zhang,Ying Han,Gaorong Han,Lei Shen

DOI: https://doi.org/10.1109/icocn59242.2023.10236171

2023-01-01

Abstract:In this paper, we report an all-fiber 4-mode fiber multiplexer and its measurement, which uses a fused tapering method to fabricate different mode-selective coupler. The insertion loss of a single mode-selective is less than 0.7dB, the insertion loss of LP 01 , LP 11 , LP 21 and LP 02 is less than 3 dB after cascading, while the modal crosstalk is lower than −15dB. This device can be applied in mode-division multiplexing transmission systems.
Silicon-on-insulator Grating Couplers for Dual-Band and Triple-Band Multiplexing

Lirong Cheng,Simei Mao,H. Y. Fu

DOI: https://doi.org/10.1364/acpc.2021.t1i.2

2021-01-01

Abstract:We demonstrate dual-band and triple-band operating grating couplers on silicon-on-insulator. These grating couplers simultaneously couple multiple bands and spatially separating them with calculated coupling efficiencies of <4 dB for all bands.
Monolithically Integrated Fiber-to-the-home Diplexers and Triplexers Using a Bilevel Etched 2×2 Optical Coupler

Li Zhang,Lei Wang,Jian-Jun He

DOI: https://doi.org/10.1364/ao.48.000f44

IF: 1.9

2009-01-01

Applied Optics

Abstract:A novel design of monolithically integrated diplexers and triplexers for fiber-to-the-home applications is presented. A bilevel etched asymmetrical 2 x 2 optical coupler is analyzed for efficient couplings of both upstream and downstream signals. The design of the diplexer is extended to a triplexer by adding an etched diffraction grating as an additional downstream demultiplexing element. The total size of the integrated diplexer and triplexer is smaller than 500 microm x 500 microm.
Dual-Wavelength-Band Grating Coupler on 220-Nm Silicon-on-Insulator with High Numerical Aperture Fiber Placed Perfectly Vertically

Lirong Cheng,Simei Mao,Xin Tu,H. Y. Fu

DOI: https://doi.org/10.1109/jlt.2021.3090172

IF: 4.7

2021-01-01

Journal of Lightwave Technology

Abstract:We propose and design a novel dual-wavelength-band grating coupler on 220-nm-thick silicon-on-insulator and experimentally investigate its capability to couple two wavelength bands simultaneously under surface-normal fiber placement. Such dual-wavelength-band operation take advantage of a dual-etch grating design not only with increased directionality but also with unique diffraction angle dispersion characteristics for the two targeted wavelength bands. The role of high numerical aperture fiber is theoretically investigated, leading to reduced angular sensitivity in general and subsequently increased coupling efficiency for our proposed dual-wavelength-band operation scheme. Our device is further fabricated using 248-nm deep-UV lithography on an 8-inch wafer for verification. The peak coupling efficiency is measured to be -5.0 dB at 1275 nm and -5.9 dB at 1519 nm for O-band and S/C-band respectively.

Dual-layer SiNx-on-SOI Grating Coupler As an Efficient Higher-Order Fiber Mode Multiplexer

Design and Numerical Optimization of A Mode Multiplexer Based on Few-Mode Fiber Couplers

A Nonreciprocal Add-Drop Multiplexer Based on Grating Assisted Couplers

Optimization of Few-Mode-Fiber Based Mode Converter for Mode Division Multiplexing Transmission

Fiber-Chip Bi-Wavelength Multiplexing with Subwavelength Single-Etch Grating Coupler and Diplexer

Silicon-on-Insulator Mode (de)multiplexer for On-Chip Mode-Division Multiplexing

Silicon Mode Multi/Demultiplexer Based on Multimode Grating-Assisted Couplers

On-chip mode multiplexer based on a single grating coupler

Dual-Wavelength-Band Multiplexed Grating Coupler on Multilayer SiN-on-SOI Photonic Integrated Platform

High-efficiency Grating Coupler Based on Fast Directional Optimization and Robust Layout Strategy in 130 Nm CMOS Process.

Three-mode All-Optical (de)multiplexing on a SOI Chip

High-efficiency Wideband SiNx-on-SOI Grating Coupler with Low Fabrication Complexity.

Silicon Photonic Integrated Circuit Mode Multiplexer

High Efficiency Grating Coupler for Coupling Between Single-Mode Fiber and SOI Waveguides

A segment-coupled six-mode multiplexer based on multi-core fiber

Novel Wavelength Multiplexer Using (<italic>N</italic> + 1) × (<italic>N</italic> + 1) Arrayed Waveguide Grating and Polarization-Combiner-Rotator on SOI Platform

Silicon Two-Mode Multi/demultiplexer Based on Tapered Couplers

Low-Loss All-Fiber Mode Multiplexers for Weakly-Coupled 4-Mode Fiber

Silicon-on-insulator Grating Couplers for Dual-Band and Triple-Band Multiplexing

Monolithically Integrated Fiber-to-the-home Diplexers and Triplexers Using a Bilevel Etched 2×2 Optical Coupler

Dual-Wavelength-Band Grating Coupler on 220-Nm Silicon-on-Insulator with High Numerical Aperture Fiber Placed Perfectly Vertically