Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

In Situ Synthesis of Core-Shell W-Cu Nanopowders for Fabricating Full-Densified and Fine-Grained Alloys with Dramatically Improved Performance

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

In-situ synthesis of core-shell structure W(WC) composite grains in W-Cu composites fabricated by infiltration

Ultrahigh strength, thermal stability and high thermal conductivity in hierarchical nanostructured Cu-W alloy

WC Strengthened W–Cu Nanocomposite Powder Synthesized by In-Situ Reactions

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Performance of a Hierarchically Nanostructured W–Cu Composite Produced via Mediating Phase Separation

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

High hardness and wear resistance of W-Cu composites achieved by elemental dissolution and interpenetrating nanostructure.

Strengthening of Copper with Homogeneous Dispersion of Nanoscale Tungsten Particles Fabricated by Spark Plasma Sintering

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Tribological and Corrosion Behaviors of Bulk CuW Nanocomposites Fabricated by Mechanical Alloying and Warm Pressing

Fabrication of Cu-riched W-Cu composites by combustion synthesis and melt-infiltration in ultrahigh-gravity field

Novel synthesis of CuW composite reinforced with lamellar precipitates via aluminothermic reduction

Preparation of TiC/W Core–shell Structured Powders by One-Step Activation and Chemical Reduction Process

Morphological Characteristics of W/Cu Composite Nanoparticles with Complex Phase Structure Synthesized via Reactive Radio Frequency (RF) Thermal Plasma

PREPARATION OF ULTRAFINE W–Cu COMPOSITE POWDER USING ULTRASONIC-ASSISTED ELECTROLESS PLATING

Microstructure and Properties of W Cu Composites with Low Copper Content at Different Sintering Temperatures

Thermal Performance Investigation of Core-Shell Cu/Al Micron-Nano Composites with Wo3

Fabrication of Ultra-Fine-Grained W-TiC Alloys by a Simple Ball-Milling and Hydrogen Reduction Method

A new design strategy for purifying and strengthening W alloy by self-decomposing in-situ nanoparticles