Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

High hardness and wear resistance of W-Cu composites achieved by elemental dissolution and interpenetrating nanostructure.

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Wear-resistance enhancement of nanostructured W-Cu-Cr composites

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Performance of a Hierarchically Nanostructured W–Cu Composite Produced via Mediating Phase Separation

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Effect of Copper on Microstructure and Performance of WC/NiAl/TiC Composite Coatings by Laser Cladding

Excellent wear resistance of multicomponent nanocrystalline W‒Cu based composite

Microstructure and high-temperature mechanical properties of Cu-W composite prepared by hot isostatic pressing

High-temperature mechanical and electrical properties of W-particle-reinforced Cu-matrix composites from improved electroless plated powders

Tribological and Corrosion Behaviors of Bulk CuW Nanocomposites Fabricated by Mechanical Alloying and Warm Pressing

Effect on Microstructure and Hardness of Reinforcement in Al–Cu with Al4C3 Nanocomposites

Fabrication and characterization of W/Cu/Ni-based high specific gravity alloy with Zr and Ti combined addition

Effect of sintering temperature on fine-grained Cu W composites with high copper

Effect of nano-Y2O3 on the microstructure and mechanical properties of Cu-10W composites prepared by spark plasma sintering

Multiphase strengthening mechanism of Cu-Y2O3/W composites prepared by mechanical alloying

Microstructure and property of electroformed nano-Al2O3/Cu composite

Engineering performance of tungsten network reinforced copper matrix composites synthesized by selective laser melting and infiltration

Ultrahigh strength, thermal stability and high thermal conductivity in hierarchical nanostructured Cu-W alloy

Strengthening of Copper with Homogeneous Dispersion of Nanoscale Tungsten Particles Fabricated by Spark Plasma Sintering