Abstract:Although icosahedral quasicrystal phase (denoted as I-phase) has been verified as an outstanding reinforcing phase, the mechanical properties of quasicrystal-reinforced Mg-Zn-Y alloys fabricated by traditional casting processes are still unsatisfactory due to the serious segregation of intermetallic compounds. In this study, the microstructure and mechanical properties of Mg-12Zn-2Y alloy fabricated by different casting processes, including permanent mold casting, squeeze casting and rheo-squeeze casting with ultrasonic vibration, were systematically investigated and compared. The results show that massive, large-sized I-phase and Mg 7 Zn 3 phase gather together in the permanent mold cast sample, while the squeeze casting process leads to the transformation of I-phase into fine lamellar morphology and the amount of Mg 7 Zn 3 decreases. As to the rheo-squeeze casting process, when the ultrasonic vibration is exerted with power from 800 W to 1,600 W, the α-Mg grains are refined and spheroidized to a large extent, and the lamellar spacing of the eutectic structure is significantly reduced, accompanied by some tiny granular I-phase scattering in the α-Mg matrix. However, when the ultrasonic power continuously increases to 2,400 W, the eutectic structure becomes coarse. The best mechanical properties of the rheo-squeeze cast alloy are obtained when the ultrasonic power is 1,600 W. The microhardness, yield strength, ultimate tensile strength and elongation are 79.9 HV, 140 MPa, 236 MPa, and 3.25%, which are 44.1%, 26.1%, 25.5%, 132.1% respectively higher than the corresponding values of the squeeze casting sample, and are 47.6%, 44.3%, 69.8%, and 253.3% respectively higher than the corresponding values of the permanent mold casting sample.

Effects of Icosahedral Phase Formation on the Microstructure and Mechanical Improvement of Mg Alloys: A Review

The Strengthening Effect of Icosahedral Phase on As-Extruded Mg–Li Alloys

Effect of Icosahedral Quasicrystalline Fraction and Extrusion Ratio on Microstructure, Mechanical Properties, and Anisotropy of Mg-Zn-Gd-Based Alloys

Effects of Icosahedral Phase on Mechanical Anisotropy of As-Extruded Mg-14Li (in Wt%) Based Alloys

Effect of Icosahedral Phase on Crystallographic Texture and Mechanical Anisotropy of Mg–4%Li Based Alloys

Quasicrystal-reinforced Mg alloys

Effect of Zn Concentration on the Microstructure and Mechanical Properties of Al-Mg-Si-Zn Alloys Processed by Gravity Die Casting

Effect of Composition on the Microstructure and Mechanical Properties of Mg–Zn–Al Alloys

Microstructure and Tensile Properties of As-Extruded Mg–Li–Zn–Gd Alloys Reinforced with Icosahedral Quasicrystal Phase

Effect of Quasicrystal Phase on Mechanical Properties and Damping Capacities of Mg–Zn–Y–Zr Alloys

Effect of quasicrystal and Laves phases on strength and ductility of as-extruded and heat treated Mg–Zn–Gd-based alloys

Microstructure Evolution and Mechanical Properties of Mg-12Zn-2Y Alloy Containing Quasicrystal Phase Fabricated by Different Casting Processes

Effect of Quasicrystal I-Phase on Microstructure and Mechanical Properties of Hot-Rolled Diphasic Mg-8 Wt.% Li Alloy

Effects of Al and Zn Contents on the Microstructure and Mechanical Properties of Mg-Al-Zn-Ca Magnesium Alloys

Effect of Icosahedral Phase on the Thermal Stability and Ageing Response of a Duplex Structured Mg–Li Alloy

Influence of Higher Zn/Y Ratio on the Microstructure and Mechanical Properties of Mg-Zn-Y-Zr Alloys

A study of the microstructure, phase composition, and mechanical properties of extruded Mg-9Er-6Y-xZn-0.6Zr magnesium alloys

Effects of extrusion on the microstructure and mechanical properties of Mg–Zn–Gd alloy reinforced with quasicrystalline particles

Effect of Icosahedral Phase on the Crystallographic Texture and Mechanical Anisotropy of Duplex Structured Mg–Li Alloys

Effects of Zn/Al Mass Ratio on Microstructure Evolution and Mechanical Properties of Mg–Sn Based Alloys

Effect of Zn and Y on microstructures and properties of normally-solidified Mg-Zn-Y alloys