Abstract:The Ti-4Al-2V (wt. %) titanium alloy has garnered widespread applications across diverse fields due to its exceptional strength-to-weight ratio, high toughness, specific strength, and corrosion resistance. The welding of Ti-4Al-2V titanium alloy components is often necessary in manufacturing processes, where the reliability of a welded joint critically influences the overall service life of these components. Consequently, a comprehensive understanding of the welded joint's microstructure and mechanical properties is imperative. In this study, Ti-4Al-2V titanium alloy was welded using multi-layer and multi-pass TIG welding techniques, and a detailed examination was conducted to analyze the microstructure and grain morphology of each microzone of the welded joint. The results revealed the presence of an initial α phase and a secondary lamellar α phase in the heat affected zone (HAZ). Meanwhile, the fusion zone (FZ) primarily comprised a coarse secondary α phase and a small amount of an acicular martensitic α' phase. Both the recrystallization zone and the superheated zone exhibited a distinct preferred orientation, with grains smaller than 10 μm accounting for 65.9% and 55.1%, respectively. To assess the mechanical properties of the various microzones and the typical microstructure within the welded joint, nanoindentation tests were performed. The results indicated that the recrystallization zone possessed a higher nanohardness (3.753 GPa) than the incomplete recrystallization zone (3.563 GPa) and the superheated zone (3.48 GPa). Among all the microzones, the FZ exhibited the lowest average nanohardness (3.058 GPa). Notably, the basket-weave microstructure demonstrated the highest average nanohardness, reaching 3.93 GPa. This was followed by the fine-grain microstructure, which possessed a slightly lower nanohardness. The Widmanstätten microstructure, on the other hand, exhibited the lowest nanohardness among the three microstructures within the HAZ. Therefore, the basket-weave microstructure stands out as the most desirable microstructure to achieve in the welded joint. In summary, this study provides a comprehensive characterization and analysis of the microstructure and properties of Ti-4Al-2V titanium alloy TIG welds, aiming to contribute to the optimization of the TIG welding process for Ti-4Al-2V titanium alloy.

Quantitative Analysis On Microstructure-Tensile Property Relationship For Ti-6al-4v Alloy With Basket Weave Structure

Microstructure-Tensile Properties Correlation for the Ti-6al-4v Titanium Alloy

Microstructure and microhardness evolution of Ti-10V-2Fe-3Al alloy under tensile/torsional deformation modes

Study on the Relationship Between Microstructure and Mechanical Property in a Metastable Β Titanium Alloy

Microscopic Strain Localization of Ti-6Al-4V Alloy Under Uniaxial Tensile Loading

Ex-situ study on mechanical properties and deformation mechanism of three typical microstructures in TA19 titanium alloy

Quantification of microstructural features and application of artificial neural network in correlation of microstructure and property of Ti-alloys

Quantitative microstructural analysis of Ti-6Al-4V alloy after hot forging process by means of stereological morphometry

Microstructures and Tensile Properties of a High Strength Β Titanium Alloy Ti5Al4Zr8Mo7V by Near Β Forging and Β-Transus Forging

Forging–microstructure–tensile properties correlation in a new near β high-strength titanium alloy

Dependence of Mechanical Properties on the Microstructure Characteristics of a Near Β Titanium Alloy Ti-7333

Investigation of the scanning strategy on the microstructure and tensile property of Ti6Al4V alloy fabricated by selective laser melting

Relationship Between Microstructures and Mechanical Properties of Ti-6Al-4V Alloy in Centrifugal Casting

Effect of Forging on Microstructures and Mechanical Properties of Ti-6321 Alloy Bar

An Investigation into the Microstructures and Mechanical Properties of a TIG Welding Joint in Ti-4Al-2V Titanium Alloy

The Microstructure And Tensile Properties Of Ti-45al-5nb-0.03y After Hot Extrusion

Microstructural Analysis of the Improved Strength–Ductility Combination in Titanium Alloy with Bi-modal Structure

Microstructure tailoring and impact toughness of a newly developed high strength Ti-5Al-3Mo-3V-2Cr-2Zr-1Nb-1Fe alloy

Microstructure evolvement of isometry TiAl under tensile impact loadings

Microstructural Evolution and Mechanical Properties of Ti-22Al-25Nb (at.%) Orthorhombic Alloy with Three Typical Microstructures

Tensile Property and Microstructure Analysis of Fine-grained High Strength 42CrMoVNbTi Steel