Abstract:Powder metallurgy (PM) α + β Ti-4Al-4Mo-4Sn-0.5Si alloys were fabricated through thermomechanical powder consolidation of TiH 2 -based powder compacts with two different processing routes: one involving blending the elemental powders (BE route) and the other involving mechanical milling a blend of elemental powders (MM route). With the MM + annealing + solution and aging (STA) route, a hierarchical microstructure consisting of necklace-like micron-scaled grain boundary α (α GB ) segments and isolated submicron-scaled primary α (α p ) rods dispersed in a β transformed structure (β t ) matrix containing a high number density of nano-scaled secondary α (α s ) laths was produced in the alloy. The alloy with the hierarchical microstructure achieved an excellent combination of a very high yield strength of 1339 MPa,an ultimate tensile strength of 1467 MPa and an excellent ductility of 10.4%. The increased strength was mainly due to the high fraction of β t matrix in which the fine-dispersed α s precipitates with different orientations efficiently blocked the dislocation motion during deformation. The excellent ductility achieved despite of the high flow stress can be attributed to the elimination of strain concentration in the α GB segments which prevented their cracking prior to the material reaching the necking point during plastic deformation. This was in contrast with the typical α/β t lamellar microstructure of the same alloy composition obtained with the BE + same heat treatment route where strain concentration in the α GB plates occurred due to the direct slip transmission from α colonies to adjacent parent α GB grains during plastic deformation, thus resulting in intergranular premature cracking. TEM observation demonstrated that the strain gradient from the α/β t interfaces to the domain interiors of both α GB segments and α p rods activated a high density of geometrically necessary dislocations near the interfaces, and caused an obvious synergistic strengthening effect which also contributed to the slow drop of strain hardening rate and thus was beneficial to improving the ductility.

Microstructures and Tensile Properties of a High Strength Β Titanium Alloy Ti5Al4Zr8Mo7V by Near Β Forging and Β-Transus Forging

Relationship Between Mechanical Properties and Microstructure in a New High Strength Β Titanium Alloy

Microstructural dependence of strength and ductility in a novel high strength β titanium alloy with Bi-modal structure

Forging–microstructure–tensile properties correlation in a new near β high-strength titanium alloy

Electron Beam Welding and Post Heat Treatment of a New Near-Beta High-Strength Ti-4Al-5Mo-5V-5Cr-1Nb Alloy

Face Centered Cubic Substructure and Improved Tensile Property in a Novel Β Titanium Alloy Ti–5Al–4Zr–10Mo–3Cr

Relationship Between Microstructure and Tensile Properties on a Near-Β Titanium Alloy after Multidirectional Forging and Heat Treatment

The Effects of Forging Strategies on Microstructures and Mechanical Properties of a Ti-5al-5mo-5v-1cr-1fe Near Β-Titanium Alloy

Tensile Brittleness and Ductility Improvement in a Novel Metastable Β Titanium Alloy with Lamella Structure

Design and microstructure-mechanical properties of a novel metastable β titanium alloy with excellent strength-plasticity matching

Achieving high strength-ductility synergy in a hierarchical structured metastable β-titanium alloy using through-transus forging

Microstructural Tailoring and Mechanical Properties of a Multi-Alloyed Near Β Titanium Alloy Ti-5321 with Various Heat Treatment

Achieving High Strength and Ductility of a Metastable Β-Titanium Alloy Via Coupling Thermomechanical Processing and Heat Treatments

Hierarchical microstructure and strain partition of a PM α + β titanium alloy with an ultrahigh strength-ductility synergy

Hierarchical Structure and Deformation Behavior of a Novel Multicomponent Β Titanium Alloy with Ultrahigh Strength

Homogeneous α-precipitation and enhanced plasticity in Ti–6Cr–5Mo–5V–4Al high-strength metastable titanium alloy with heterogenous β-structure

Microstructure evolution and mechanical properties of a novel beta γ-TiAl alloy

Achieving super-high strength and acceptable plasticity for a near β-type Ti-4.5Mo-5.1Al-1.8Zr-1.1Sn-2.5Cr-2.9Zn alloy through manipulating hierarchical microstructure

A Novel High-Strength Β-Ti Alloy with Hierarchical Distribution of Α-Phase: the Superior Combination of Strength and Ductility

Achieving Synergy Between Strength and Ductility in Metastable Β-Titanium Alloy Through a Novel Multi-Morphological Microstructure

Design of Metastable Β-Ti Alloys with Enhanced Mechanical Properties by Coupling Αs Precipitation Strengthening and TRIP Effect