Abstract:Powder metallurgy (PM) α + β Ti-4Al-4Mo-4Sn-0.5Si alloys were fabricated through thermomechanical powder consolidation of TiH 2 -based powder compacts with two different processing routes: one involving blending the elemental powders (BE route) and the other involving mechanical milling a blend of elemental powders (MM route). With the MM + annealing + solution and aging (STA) route, a hierarchical microstructure consisting of necklace-like micron-scaled grain boundary α (α GB ) segments and isolated submicron-scaled primary α (α p ) rods dispersed in a β transformed structure (β t ) matrix containing a high number density of nano-scaled secondary α (α s ) laths was produced in the alloy. The alloy with the hierarchical microstructure achieved an excellent combination of a very high yield strength of 1339 MPa,an ultimate tensile strength of 1467 MPa and an excellent ductility of 10.4%. The increased strength was mainly due to the high fraction of β t matrix in which the fine-dispersed α s precipitates with different orientations efficiently blocked the dislocation motion during deformation. The excellent ductility achieved despite of the high flow stress can be attributed to the elimination of strain concentration in the α GB segments which prevented their cracking prior to the material reaching the necking point during plastic deformation. This was in contrast with the typical α/β t lamellar microstructure of the same alloy composition obtained with the BE + same heat treatment route where strain concentration in the α GB plates occurred due to the direct slip transmission from α colonies to adjacent parent α GB grains during plastic deformation, thus resulting in intergranular premature cracking. TEM observation demonstrated that the strain gradient from the α/β t interfaces to the domain interiors of both α GB segments and α p rods activated a high density of geometrically necessary dislocations near the interfaces, and caused an obvious synergistic strengthening effect which also contributed to the slow drop of strain hardening rate and thus was beneficial to improving the ductility.

Microstructural Analysis of the Improved Strength–Ductility Combination in Titanium Alloy with Bi-modal Structure

Microstructural dependence of strength and ductility in a novel high strength β titanium alloy with Bi-modal structure

Enhancing Ductility of Titanium Matrix Composites by Multimodal Α-Grains

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Microstructures and Tensile Properties of a High Strength Β Titanium Alloy Ti5Al4Zr8Mo7V by Near Β Forging and Β-Transus Forging

Achieving Synergy Between Strength and Ductility in Metastable Β-Titanium Alloy Through a Novel Multi-Morphological Microstructure

Tensile Brittleness and Ductility Improvement in a Novel Metastable Β Titanium Alloy with Lamella Structure

Enhanced Mechanical Properties of Ti-5Al-5Mo-5V-3Cr-1Zr by Bimodal Lamellar Precipitate Microstructures Via Two-Step Aging

Face Centered Cubic Substructure and Improved Tensile Property in a Novel Β Titanium Alloy Ti–5Al–4Zr–10Mo–3Cr

Combination of multiple strengthening mechanisms facilitates excellent strength-ductility balance in metastable β titanium alloy

Microstructural Sensitivity and Deformation Micro-Mechanisms of a Bimodal Metastable Β Titanium Ti–7Mo–3Nb–3Cr–3Al Alloy

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Enhancement of tensile strength and ductility of titanium with a bimodal structure

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Enhancement of Strength-Ductility Synergy in High-Strength Metastable Β-Titanium Alloys Through Boron Microalloying

Design and microstructure-mechanical properties of a novel metastable β titanium alloy with excellent strength-plasticity matching

Slip Behavior of Bi-modal Structure in a Metastable Β Titanium Alloy During Tensile Deformation

Heterogeneous Precipitate Microstructure in Titanium Alloys for Simultaneous Improvement of Strength and Ductility

Forging–microstructure–tensile properties correlation in a new near β high-strength titanium alloy

Hierarchical microstructure and strain partition of a PM α + β titanium alloy with an ultrahigh strength-ductility synergy

Achieving High Strength and Ductility of a Metastable Β-Titanium Alloy Via Coupling Thermomechanical Processing and Heat Treatments