Abstract:Powder metallurgy (PM) α + β Ti-4Al-4Mo-4Sn-0.5Si alloys were fabricated through thermomechanical powder consolidation of TiH 2 -based powder compacts with two different processing routes: one involving blending the elemental powders (BE route) and the other involving mechanical milling a blend of elemental powders (MM route). With the MM + annealing + solution and aging (STA) route, a hierarchical microstructure consisting of necklace-like micron-scaled grain boundary α (α GB ) segments and isolated submicron-scaled primary α (α p ) rods dispersed in a β transformed structure (β t ) matrix containing a high number density of nano-scaled secondary α (α s ) laths was produced in the alloy. The alloy with the hierarchical microstructure achieved an excellent combination of a very high yield strength of 1339 MPa,an ultimate tensile strength of 1467 MPa and an excellent ductility of 10.4%. The increased strength was mainly due to the high fraction of β t matrix in which the fine-dispersed α s precipitates with different orientations efficiently blocked the dislocation motion during deformation. The excellent ductility achieved despite of the high flow stress can be attributed to the elimination of strain concentration in the α GB segments which prevented their cracking prior to the material reaching the necking point during plastic deformation. This was in contrast with the typical α/β t lamellar microstructure of the same alloy composition obtained with the BE + same heat treatment route where strain concentration in the α GB plates occurred due to the direct slip transmission from α colonies to adjacent parent α GB grains during plastic deformation, thus resulting in intergranular premature cracking. TEM observation demonstrated that the strain gradient from the α/β t interfaces to the domain interiors of both α GB segments and α p rods activated a high density of geometrically necessary dislocations near the interfaces, and caused an obvious synergistic strengthening effect which also contributed to the slow drop of strain hardening rate and thus was beneficial to improving the ductility.

Combination of multiple strengthening mechanisms facilitates excellent strength-ductility balance in metastable β titanium alloy

Enhancing Ductility of Titanium Matrix Composites by Multimodal Α-Grains

Enhanced yield strength by fine grain strengthening and TRIP/TWIP effect of metastable β-type Ti-4V-2Mo-2Fe alloy with high ductility

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Achieving high strength-ductility synergy in a hierarchical structured metastable β-titanium alloy using through-transus forging

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Achieving Large Near-Linear Elasticity, Low Modulus, and High Strength in a Metastable Β-Ti Alloy by Mild Cold Rolling

Homogeneous α-precipitation and enhanced plasticity in Ti–6Cr–5Mo–5V–4Al high-strength metastable titanium alloy with heterogenous β-structure

Hierarchical microstructure and strain partition of a PM α + β titanium alloy with an ultrahigh strength-ductility synergy

Enhanced Mechanical Properties of Ti-5Al-5Mo-5V-3Cr-1Zr by Bimodal Lamellar Precipitate Microstructures Via Two-Step Aging

Achieving super-high strength and acceptable plasticity for a near β-type Ti-4.5Mo-5.1Al-1.8Zr-1.1Sn-2.5Cr-2.9Zn alloy through manipulating hierarchical microstructure

Design and microstructure-mechanical properties of a novel metastable β titanium alloy with excellent strength-plasticity matching

Unveiling the impact of heat treatment on powder-metallurgy α+β titanium alloy for achieving a superior strength-ductility combination

Sustaining an excellent strength-ductility combination of a PM α + β titanium alloy with fine prior β grains and heterogeneous microstructure

Breaking the high-temperature strength-ductility trade-off in TiAl alloys through microstructural optimization

Enhanced strength of dual-phase Ti6242 alloy via a heterogeneous microstructure

Strength enhancement of a bi-lamellar PM Ti–6Al–4V alloy without sacrificing ductility by Al partitioning and twinning-induced plasticity effect

Oxygen interstitials make metastable β titanium alloys strong and ductile

Forging–microstructure–tensile properties correlation in a new near β high-strength titanium alloy

Strengthening of a Near β-Ti Alloy through β Grain Refinement and Stress-Induced α Precipitation