Abstract:The tensile behavior of Ti6Al4V–5Cu alloy studied in the temperature range of 450–550 °C at the strain rate interval of 10 −3 -10 −1 s −1 . Alloy deformation behavior, microstructure evolution, and its relative internal structure changes due to deformation were investigated. The tensile behavior of the alloy had elucidated in terms of change in true stress-strain relationship. At 450 °C, the alloy showed the decrease of peak stress at the strain rate interval of 10 −3 -10 −2 s −1 , which suggests Ti6Al4V–5Cu plastic flow behavior, was quite different. The alloy exhibited an elongation (El) of 28% at 450 °C in a strain rate of 10 −3 s −1 . At 10 −3 s −1 , the El of the alloy decreased with the increase of forming temperature. However, at 10 −2 s −1 and 10 −1 s −1 , the El increased with the rising of temperature. Scanning electron microscope (SEM) was used to investigate the microstructure of Ti6Al4V–5Cu alloy. The alloy grain boundaries (GBs) were found as continuous and discontinuous structural features, especially the high angle grain boundaries (HAGBs). The GB feature has contributed to the initiation of micro-cracks because of the creation of weakest regions in the material during deformation. The nature of GB geometry has also a tremendous contribution to the workability of Ti6Al4V–5Cu alloy at low forming temperatures. The presence of a high amount (%) LAGBs and the serrated nature of HAGBs structures determined the pull to grain pieces. The deformation mechanism of the Ti6Al4V–5Cu alloy at low forming temperatures was accomplished initially by boundary serration phenomenon due to strain-induced GB migration related to heat treatment at low strain condition, then by initiation of recrystallized grains-triggered by the plasticity behavior of strain induced sub-boundaries, and finally by the development of deformed grains generated by the reduction in corrugation propensity of GBs due to high strain condition.

Microstructure evolvement of isometry TiAl under tensile impact loadings

Microstructure Evolution of Near Gamma TiAl Intermetallic under Tensile Impact Loadings at High Temperatures

Dynamic behavior and fracture mode of TiAl intermetallics with different microstructures at elevated temperatures

Study on high temperature tensile constitutive behavior and deformation mechanism of Ti-47.5Al-2.5 V-1.0Cr-0.2Zr alloy

Investigation on the microstructure evolution and dynamic recrystallization mechanisms of TiAl alloy at elevated temperature

Tensile Impact Behavior and Deformation Mechanism of Duplex TiAl Intermetallics at Elevated Temperatures

High-temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy

Influence of strain rates on deformation mechanism of duplex TiAl intermetallics

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

The Microstructures and Deformation Mechanism of Hetero-Structured Pure Ti under High Strain Rates

Study on the dynamic deformation behavior and microstructure evolution of Ti-5Al-2.5Sn utilized Quasi-In-Situ method

Effect of Microstructure on High-Speed Tensile Mechanical Properties of Ti-1300 Alloy

Microstructure and microhardness evolution of Ti-10V-2Fe-3Al alloy under tensile/torsional deformation modes

Microstructure evolution of a forged TiAl-Nb alloy during high-temperature tensile testing

Dynamic Strain-Rate Effect On Uniaxial Tension Deformation Of Ti5al2.5sn Alpha-Titanium Alloy At Various Temperatures

Microstructural characteristics and recrystallization mechanism of Ti-6.5Al–2Zr–1Mo–1V alloy during two-stage hot deformation

Microstructure evolution, tensile properties and internal structure transformation study on Ti6Al4V–5Cu anti-bacterial alloy during uniaxial tensile straining at low forming temperature

Tensile impact behavior of duplex Ti-46.5Al-2Nb-2Cr at elevated temperatures

Strain rate effect on the tensile behavior of Duplex Ti–46.5Al–2Nb–2Cr intermetallics at elevated temperatures

Microstructure Evolution of a Ti–Al–Sn–Zr Based Alloy During the Hot Compression Deformation