Abstract:The effect of solidification sequence on the microstructure and mechanical properties of die-cast Al-11Si-2Cu-Fe alloy is reported. Metallographic and image analysis techniques have been used to quantitatively examine the microstructural evolution at different positions of the same casting. For the thin wall thickness (3 mm), the microstructure of the alloy remains unchanged between the surface and the center of the casting. With the distance from the same surface increasing from 0 mm to 3 mm for the thick wall thickness (6 mm), the volume fraction of primary alpha-Al phases increases from 76% to 86.6%, the size of primary alpha-Al phase from 20 mm to 40 mm, the average length of eutectic Si from 3.4 mu m to 15.6 mu m, the average length of alpha-AlFeMnSi phase decreases, the brittle beta-AlFeSi forms and the volume fraction of porosity rises from 0.017% to 0.328%. These changes contribute to the reduction in the ultimate tensile strength from 300.1 MPa to 210.1 MPa, in the elongation from 1.78% to 0.81%, and the quality index (Q) from 333.7 MPa to 196.4 MPa. A typical brittle fracture is observed on the tensile fracture surface. As the solidification time decreases, the smooth flat areas become small and the amount of tearing ridges increases. (C) 2015 Elsevier B.V. All rights reserved.

Semi-solid Isothermal Heat Treatment Microstructure Evolution of Die-casting Al-5Mg-2Si-Mn Alloy

Semisolid Die-Casting Process of Mg-20Al-0.8Zn Magnesium Alloy

Microstructure Evolution of Semi-Solid Mg-14Al-0.5Mn Alloys During Isothermal Heat Treatment

Melt Superheating on the Microstructure and Mechanical Properties of Diecast Al-Mg-Si-Mn Alloy

Microstructure and Properties of Mg-5Al-1.5Ca-0.4Zn Based Alloyby Semi-Solid Isothermal Heat-Treatment-die-pressure-casting Process

Micro-Structural Evolution of Alcu5mncdva Cast Aluminum Alloy by Semi-Solid Isothermal Annealing Process

Behavior of microstructure evolution of ZL205A cast aluminum alloy during semi-solid isothermal annealing process

Effect of Solutionising and Ageing on the Microstructure and Mechanical Properties of a High Strength Die-Cast Al–Mg–Zn–Si Alloy

Semi-solid Rheocasting and Performance of Al-6.5％Mg Alloy

Synergistic Effects of Composition and Heat Treatment on Microstructure and Properties of Vacuum Die Cast Al-Si-Mg-Mn Alloys

Influence of Die Casting Temperature and T1 Treatment on the Microstructure and Properties of the Alsicumg Alloy

Effect of Holding Time on Microstructure of Mg-9Al-1Si Alloy During Semisolid Isothermal Heat Treatment

Probe on Semi-solid Forming Process of AlMg5Si2Mn Aluminum Alloy by Isothermal Heat Treatment Method

Effect of Solid-Solution Treatment on Microstructure and Hardness of Die-Casting Mg-9Al-1Zn-0.2Mn Alloy

Study on microstructure and thermal conductivity of semi-solid die casting aluminum alloy

Solidifying Pressure and Microstructure of AlSi10Cu3 in Die Sleeve in High Pressure Die Casting

Microstructures of an AlSi 7 Mg Alloy by Near-Liquidus Casting

Effect of Semi-Solid Isothermal Heat Treatment on the Microstructure of Mg–6A1–1Zn–0.7Si Alloy

Comparison of the semisolid squeeze casting and gravity casting process on the precipitation behavior and mechanical properties of the Al-Si-Cu-Mg alloy

Influence Of Solidification Parameters On The Microstructure And Properties Of Dz125 Superalloy Castings

Effect of Solidification Sequence on the Microstructure and Mechanical Properties of Die-Cast Al–11Si–2Cu–Fe Alloy