Abstract:Laser powder bed fusion (PBF-LB) additive manufacturing (AM) has shown significant promising potential in the fabrication of complex-shaped Nd-Fe-B magnets. However, a challenge arises when printing Nd-Fe-B magnets due to their inherent hardness and brittleness. The large thermal stresses caused by rapid cooling rates and steep temperature gradients easily lead to cracking, substantially degrading their magnetic properties. In the present work, an effective laser in-situ re-scanning strategy is proposed to manufacture Nd-Fe-B magnets by the PBF-LB process since it can mitigate residual stress within the deposited magnets and alleviate the cracking tendency, and its effect on the microstructure and cracking behavior is comprehensively investigated through experimental characterization and numerical simulation. The results indicate that the predominant cracks in the PBF-LB-processed Nd-Fe-B magnet deposits are transcrystalline cracks. It is observed that the crack density in the magnet deposit is efficiently reduced, and the corresponding magnetic properties are enhanced by adopting an optimized laser in-situ re-scanning strategy. This is attributed to the reduction of both the thermal gradient and related stresses in the magnet deposit. Especially, the proposed strategy also promotes the consistency of the grain size of the hard magnetic Nd 2 Fe 14 B phase, contributing to the enhancement of coercivity, without generating undesirable phases in the magnets. As a result, a higher relative density of 96.73 %, coercivity of 718 kA/m, remanence of 0.85 T, and maximum energy product of 85.9 kJ/m 3 are achieved in the PBF-LB-processed Nd-Fe-B magnet deposits from MQP-S powder, which is superior to previously reported results. The present findings provide new insights for the PBF-LB-processed high-performance Nd-Fe-B magnets with crack-free.

Characterization of Melt-Spun Ndfeb Magnets Prepared by Explosive Compaction

Magnetostriction and electrical resistivity of Sm0.88Nd0.12Fe1.93 bonded composites

Study on Warm Compaction Process of Isotropic Ndfeb Bonded Magnet

Bulk Alpha-Fe/Nd2fe14b Nanocomposite Magnets Prepared by the Phase Transition of Amorphous Nd9fe81co3nb1b6 under High Pressure

Impact of the Surface Irregularities of NiFeMo Compacted Powder Particles on Irreversible Magnetization Processes

Compression Molding of Anisotropic Ndfeb Bonded Magnets in a Polycarbonate Matrix

Influence of Fabrication Process on Magnetic Properties of Co-Finemet Nanocrystalline Powder Core

Preparation of Anisotropic Bonded NdFeB/SmFeN Hybrid Magnets by Mixing Two Different Size Powders

Microstructure And Magnetic Properties Of Bulk Nanocomposite Magnets Prepared By Crystallizing Amorphous Nd3.6pr5.4fe80co3b7nb1 Under High Pressure

Packing bimodal magnetic particles to fabricate highly dense anisotropic rare earth bonded permanent magnets

An effective laser in-situ re-scanning strategy in laser powder bed fusion of Nd-Fe-B permanent magnets: Crack reduction and magnetic properties enhancement

Comparison and process study of hot-pressed and hot-deformed Nd-Fe-B magnets prepared by amorphous and nanocrystalline powders

The effect of density distribution on alignment uniformity of Nd-Fe-B compact: Discrete element method (DEM) and experiments

Fabrication of highly dense isotropic Nd-Fe-B bonded magnets via extrusion-based additive manufacturing

High Performance Rare Earth Nd-Fe-B Bonded Magnets

Improvement of overall texture and magnetic properties in bulk hot-deformed Nd-Fe-B composite magnets by the design of macrostructure

Microstructure and magnetic properties of Nanomet compacted by spark plasma sintering

Effect of ingot preparation technique on magnetic properties of NdFeB magnets

Bulk Α-Fe/nd2fe14b Nanocomposite Magnets Produced by Severe Plastic Deformation Combined with Thermal Annealing

Laser Powder Bed Fusion of Sm-Fe-N Bonded Magnets Employing Flake Powders.

Amorphous-crystalline nanostructured Nd-Fe-B permanent magnets using laser powder bed fusion: Metallurgy and magnetic properties