Abstract:Here, a new Mg-1Bi-1Mn-0.3Zn (BMZ110, wt%) wrought alloy designed by the dilute addition of Zn subjected to an appropriate extrusion processing that showed an excellent strength-ductility synergy at room temperature. The main results included four aspects as follows: 1) With dilute Zn addition, the as-cast BMZ110 alloy was refined into an approximately equiaxed-grained structure, since the solid solution of Zn provided a relatively high growth restriction factor. 2) The as-extruded BMZ110 alloy exhibited the finer average grain size and weaker basal texture intensity than the as-extruded BM11 alloy without Zn. The co-segregation of Bi and Zn solutes into grain boundaries was observed to impede grain growth during extrusion and further weaken texture intensity. Moreover, Zn atoms incorporated into Mg3Bi2 phases by replacing Bi atoms increasing the nucleation rate of Mg3Bi2 phases and refining their sizes. 3) Compared with the as-extruded BM11 alloy, the as-extruded BMZ110 alloy demonstrated the higher yield strength (~ 283.4 MPa), ultimate strength (~ 366.2 MPa) and elongation-to-failure (~ 26%). The size refinement of grains and second phases contributed to an extra strength increments. Grain boundary segregation enhanced grain boundary cohesion not only reducing the number density of grain boundary cracks, but also activating more slip modes and grain rotation for increasing the ductility. 4) The as-extruded BMZ110 alloy had the higher grain growth resistance than the as-extruded BM11 alloy during annealing. Solute segregation offered an effective obstacle to restrict grain boundary migration enlarging the activation energy (~ 112.2 kJ/mol) and further delaying the grain growth. Therefore, this work will be helpful for the development of new high performance low-alloyed Mg-Bi based wrought alloys to achieve extensive applications in industries.

Design of Multicomponent Mg–Al–Zn–Sn–Bi Alloys with Refined Microstructure and Enhanced Tensile Properties

A high-performance Mg-Al-Sn-Zn-Bi alloy fabricated by combining sub-rapid solidification and hot rolling

Ultra strength-ductility synergy in the Mg-Al-Zn alloy via densely dispersed multi-scale {1012‾} tension twins

Ultra strength-ductility synergy in the Mg-Al-Zn alloy via densely dispersed multi-scale {10<mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si1.svg"><mml:mrow><mml:mover accent="true"><mml:mn>12</mml:mn><mml:mo>¯</mml:mo></mml:mover></mml:mrow></mml:math>} tension twins

Development of low-alloyed Mg–Zn–Ca–Sn–Mn alloy with high strength-ductility synergy by sub-rapid solidification and hot rolling

Exploiting an as-extruded fine-grained Mg-Bi-Mn alloy with strength-ductility synergy via dilute Zn addition

Effect of a bimodal grain structure on corrosion behavior and tensile properties of low-alloyed Mg-1Bi-1Zn-1Ag alloy

Study on the microstructure and mechanical properties of Mg–Al–Li–Zn–Ti multi-component alloy

Novel Mg–Al–Sn–Zn–Y Alloys with Enhanced Strength−Ductility Combination Prepared by Hard‐Plate Rolling

Effect of Ca addition on microstructure and mechanical properties of Mg–3.8Al–1.1Sn alloys

Effect of composition on the microstructure and mechanical properties of Mg-Al-Zn alloys

Tailoring bimodal grain structure of Mg-9Al-1Zn alloy for strength-ductility synergy: Co-regulating effect from coarse Al2Y and submicron Mg17Al12 particles

Enhanced ductility and strength of Mg-1Zn-1Sn-0.3Y-0.2Ca alloy achieved by novel micro-texture design

Microstructural Characteristics and Mechanical Properties of Extruded Al-4Cu-1Li-0.4Mg-0.1Zr-xZn Alloy

Microstructures and Properties of Biomedical Mg-Zn-Sn-Zr Rolled Alloys

Low-cost and high-strength Mg-Al-Ca-Zn-Mn wrought alloy with balanced ductility

Improving mechanical properties of Mg-Sn alloys by co-addition of Li and Al

Microstructure characteristics of an ultra-high strength extruded Al-4.7Cu–1Li-0.5Mg-0.1Zr–1Zn alloy during heat treatment

Achieving Low Tension-Compression Yield Asymmetry and Ultrahigh Strength in Mg–1Al–1Ca–0.2Mn (wt%) Alloy Via Sub-Micron Grain Refinement

Microstructures and Mechanical Properties of a High-Strength Mg-3.5Sm-0.6Zn-0.5Zr Alloy

Achieving high strength near 400 MPa in an ultra-fine grained Mg–Bi–Ca ternary alloy via low-temperature extrusion