Abstract:For further efficiency improvement in kesterite-type Cu2ZnSn(S,Se)4 (CZTSSe) solar cells, it is essential to address the carrier recombination issue at the back electrode interface (BEI) caused by the undesirable built-in potential orientation toward an absorber as an n-MoSe2 interfacial layer formed. In this regard, back surface field (BSF) incorporation, i.e., field-effect passivation, shows promise for dealing with this issue due to its positive effect in decreasing recombination at the BEI. In this study, the BSF was realized with the p-type conduction transition in interfacial layer MoSe2 by incorporating Nb into the back electrode. The BSF width can be tuned via modulating the carrier concentration of the absorber, which has been demonstrated by capacitance–voltage characterization. A beyond 7% efficiency BSF-applied CZTSSe solar cell is prepared, and the effects of a tunable BSF and the mechanism underpinning device performance improvement have been investigated in detail. The wider BSF distribution in the absorber induces a decrease in reverse saturation current density (J0) due to the stronger BSF effect in suppressing BEI recombination. As a result, an accompanying increase in open-circuit voltage (VOC) and short-circuit current density (JSC) is achieved as compared to the BSF-free case. This study offers an alternative strategy to address the BEI recombination issue and also broadens the interface passivation research scope of potentially competitive kesterite solar cells.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c10561?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c10561</a>.EDS spectrum of a Mo:Nb film grown on the SLG substrate and statistical histograms of the absorber grain size distribution from the SEM images in <a class="internalNav" href="#fig5">Figure </a><a class="internalNav" href="#fig5">5</a>a,b; composition ratios in CZTS precursor solution; the compositions of MoSe2 and MoSe2:Nb films measured via EDS and XPS and those of CZTSSe films prepared on the SLG substrate measured by EDS (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c10561/suppl_file/am0c10561_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

MoO2 Sacrificial Layer for Optimizing Back Contact Interface of Cu2ZnSn(S,Se)4 Solar Cells

Back Contact Engineering to Improve CZTSSe Solar Cell Performance by Inserting MoO3 Sacrificial Nanolayers

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Differential effects of MoO3 and MoO2 sacrificial layer on J-V performance of Cu2ZnSn (S, Se)4 solar cells

Investigation in Feasibility of Molybdenum As A Back Contact Layer for Silicon Based Quantum Dot Solar Cells

Modification of Back Contact in Cu 2 ZnSnS 4 Solar Cell by Inserting Al-Doped ZnO Intermediate Layer

Interface passivation and band alignment of high efficiency Cu(In, Ga)Se2 solar cells: Application of Mo(OxSe1-x)2 buffer layer at Mo/ Cu(In, Ga)Se2 interface

Role of zinc tin oxide passivation layer at back electrode interface in improving efficiency of Cu2ZnSn(S,Se)4 solar cells

Comparative Study on Effect of Mo–Cr Bilayer and Mo Back Electrodes on Performance of Cu2ZnSn(S, Se)4 Solar Cell

Facile Tailor on the Surface of Mo Foil Toward High‐Efficient Flexible CZTSSe Solar Cells

Interfacial Engineering to Improve Cu2ZnSnX4 (X = S, Se) Solar Cell Efficiency

Significant Passivation Effect of Cu(In, Ga)Se 2 Solar Cells via Back Contact Surface Modification Using Oxygen Plasma

All‐Solution‐Processed Cu2ZnSnS4 Solar Cells with Self‐Depleted Na2S Back Contact Modification Layer

Introducing Bi2S3 Interlayer to Synergistically Modify Mo Back Contact and Regulate Bulk Defects in Kesterite Solar Cells

Low Oxygen Content MoOx and SiOx Tunnel Layer Based Heterocontacts for Efficient and Stable Crystalline Silicon Solar Cells Approaching 22% Efficiency

A DMSO/MOE mixed solvent system for improving the morphology and efficiency of kesterite solar cell

Effect of back contact surface nitriding on the growth of Cu2ZnSnSe4 and solar cells performances

Enhancement in the efficiency of Sb2(S,Se)3 thin-film solar cells with Spin-coating NiOx as the hole transport layer

Optimizing the window layer for achieving over 10% efficient Cu2ZnSn(S,Se)4 solar cells

Modulation of Field-Effect Passivation at the Back Electrode Interface Enabling Efficient Kesterite-Type Cu 2 ZnSn(S,Se) 4 Thin-Film Solar Cells