Abstract:A novel finding that the electrochemical performance of the commercial lithium titanate (Li 4 Ti 5 O 12 , LTO) can be significantly improved by using a novel current collector of CuI particles modified copper foil is reported for the first time in this work. Firstly, a large number of particles with well-defined shapes were prepared on the commercial copper foil surface via a very simple soaking process, in which the soaking solution contained only CuSO 4 , H 2 SO 4 and [Bmim]I. As indicated by the XRD and XPS measurements, the particles observed on the surface of the copper foil were identified as CuI particles. That is, CuI particles modified copper foils (denoted as CuI/Cu) were successfully prepared at room temperature. CuI/Cu prepared in the presence of 0.4, 0.6 and 0.8 g of [Bmim]I were nominated as CF (copper foil) a, b and c, respectively. Inconceivably, as compared to the conventional LTO electrode, the LTO electrodes assembled using the newly prepared CFs exhibited a significantly improved electrochemical performance, i.e., all as-prepared CFs showed an evident promoting effect on the electrochemical performance of the traditional LTO electrodes. For instance, the initial discharge capacity (DC) of the LTO electrode assembled using CF b (called electrode b) at 0.2 C was 307 mAh g −1 , which was about 1.86 times higher than that of the LTO electrode prepared using the conventional copper foil current collector (165 mAh g −1 ). Particularly, as the applied current rate was as high as 10 C, the DC value of electrode b (117 mAh g −1 ), even after 100 cycles, was still about 2.54 times that of the traditional LTO electrode (46 mAh g −1 ). In this preliminary work, a new method for preparing CuI particles was developed, along with a novel approach to significantly improve the electrochemical properties of the commercial LTO electrode. The method did not require any strong oxidants or reducing agents, nor did it demand any additional energy expenditure during the preparation of CuI particles. Moreover, the approach did not require any changes in the assembly procedure for the LTO electrodes being studied. This work was very meaningful for the development of the CuI-related research field as well as for the electrochemical performance improvement of LTO-based lithium-ion batteries (LIBs).

In Situ Preparation of CuCl Cubic Particles on the Commercial Copper Foil: Its Significant Facilitation to the Electrochemical Performance of the Commercial Graphite and Its Unexpected Photochromic Behavior

Preparation and electrochemical corrosion behaviour of 3D large-sized nanocrystalline copper bulk in solutions with chloride ions

Preparation of CuBr Nanoparticles on the Surface of the Commercial Copper Foil Via a Soaking Method at Room Temperature: Its Unexpected Facilitation to the Discharge Capacity of the Commercial Graphite Electrode

Promoting Effect of Cobblestone-shaped CuI Nanoparticles Immobilized on the Copper Foil Surface on the Electrochemical Performance of the Conventional Graphite Electrode

In Situ Preparation and Determination of Electrochemical and Electrochromic Properties of Copper Phthalocyanine-Polyaniline Nanocomposite Films

Lithium insertion in naturally surface-oxidized copper

A novel approach for the preparation of textured CuO thin films from electrodeposited CuCl and CuBr

Self-assembled Cube-like Copper Oxide Derived from a Metal-Organic Framework as a High-Performance Electrochemical Supercapacitive Electrode Material

Electrochemical Thin Film Deposition of Copper(I) Halides in Aqueous Solution: Substrate Extension and Structure Transformation

Preparation, micro-structure and characterization of high strength and low profile lithium copper foil with SPS and HP additives

Significantly improved electrochemical performance of the commercial lithium titanate (Li4Ti5O12) achieved by using a novel current collector of cuprous iodide-modified copper foil

Synthesis of non-planar graphene-wrapped copper nanoparticles with iron(III) oxide decoration for high performance supercapacitors

An Ionic Liquid-Present Immersion Method for Preparing Cotton Fiber-Shaped Cu2O Nanoparticles at Room Temperature

Unraveling the Mechanism of Chalcopyrite’s Superior Performance for Lithium Storage

Nanograined Copper Foil As a High-Performance Collector for Lithium-Ion Batteries

Multi-scan Cyclic Voltammetry to Roughen the Surface of Copper Foil for Application in Copper-Clad Laminates

Electrochemical double-pulse technique to modulate the roughened surface of copper foil for copper-clad laminates

Preparation of CuO Nanoparticles Film on Cu Substrate by Air Cold Plasma and Its Photoelectrochemical Properties

Preparation and Electrochemical Performance of a CuO/graphene Composite

Preparation and electrochemical performances of cubic shape Cu2O as anode material for lithium ion batteries

Preparation of Micron Size Cuprous Oxide Powder from Acidic CuCl2 Etchant Waste Solution