Abstract:A novel finding that the electrochemical performance of the commercial lithium titanate (Li 4 Ti 5 O 12 , LTO) can be significantly improved by using a novel current collector of CuI particles modified copper foil is reported for the first time in this work. Firstly, a large number of particles with well-defined shapes were prepared on the commercial copper foil surface via a very simple soaking process, in which the soaking solution contained only CuSO 4 , H 2 SO 4 and [Bmim]I. As indicated by the XRD and XPS measurements, the particles observed on the surface of the copper foil were identified as CuI particles. That is, CuI particles modified copper foils (denoted as CuI/Cu) were successfully prepared at room temperature. CuI/Cu prepared in the presence of 0.4, 0.6 and 0.8 g of [Bmim]I were nominated as CF (copper foil) a, b and c, respectively. Inconceivably, as compared to the conventional LTO electrode, the LTO electrodes assembled using the newly prepared CFs exhibited a significantly improved electrochemical performance, i.e., all as-prepared CFs showed an evident promoting effect on the electrochemical performance of the traditional LTO electrodes. For instance, the initial discharge capacity (DC) of the LTO electrode assembled using CF b (called electrode b) at 0.2 C was 307 mAh g −1 , which was about 1.86 times higher than that of the LTO electrode prepared using the conventional copper foil current collector (165 mAh g −1 ). Particularly, as the applied current rate was as high as 10 C, the DC value of electrode b (117 mAh g −1 ), even after 100 cycles, was still about 2.54 times that of the traditional LTO electrode (46 mAh g −1 ). In this preliminary work, a new method for preparing CuI particles was developed, along with a novel approach to significantly improve the electrochemical properties of the commercial LTO electrode. The method did not require any strong oxidants or reducing agents, nor did it demand any additional energy expenditure during the preparation of CuI particles. Moreover, the approach did not require any changes in the assembly procedure for the LTO electrodes being studied. This work was very meaningful for the development of the CuI-related research field as well as for the electrochemical performance improvement of LTO-based lithium-ion batteries (LIBs).

Preparation of CuBr Nanoparticles on the Surface of the Commercial Copper Foil Via a Soaking Method at Room Temperature: Its Unexpected Facilitation to the Discharge Capacity of the Commercial Graphite Electrode

Promoting Effect of Cobblestone-shaped CuI Nanoparticles Immobilized on the Copper Foil Surface on the Electrochemical Performance of the Conventional Graphite Electrode

In Situ Preparation of CuCl Cubic Particles on the Commercial Copper Foil: Its Significant Facilitation to the Electrochemical Performance of the Commercial Graphite and Its Unexpected Photochromic Behavior

Nanograined Copper Foil As a High-Performance Collector for Lithium-Ion Batteries

Organic carbonized copper foil facilitates the performance of current collector for lithium-ion batteries

Br-doped Cu nanoparticle formed by in situ restructuring for highly efficient electrochemical reduction of CO2 to formate

An Ionic Liquid-Present Immersion Method for Preparing Cotton Fiber-Shaped Cu2O Nanoparticles at Room Temperature

Manipulating Cu Nanoparticle Surface Oxidation States Tunes Catalytic Selectivity Toward CH4 or C2+ Products in CO2 Electroreduction

Microcrystalline copper foil as a high performance collector for lithium-ion batteries

Lithiophilic Ag Nanoparticle Layer on Cu Current Collector toward Stable Li Metal Anode

Cu Nanoparticles Derived from CuO Electrodes in Lithium Cells

Lithium insertion in naturally surface-oxidized copper

Preparation of 3d Nanoporous Copper-Supported Cuprous Oxide for High-Performance Lithium Ion Battery Anodes

Lithiophilic Hyperbranched Cu Nanostructure for Stable Li Metal Anodes

Large‐Scale Modification of Commercial Copper Foil with Lithiophilic Metal Layer for Li Metal Battery

Preparation of the Porous Copper Foil Current Collector for High-Performance Lithium-Ion Batteries by Electro-Codeposition: Effect of Stirring Speed

Preparation of a Nanoporous CuO/Cu Composite Using a Dealloy Method for High Performance Lithium-Ion Batteries

One-stone, two birds: One step regeneration of discarded copper foil in zinc battery for dendrite-free lithium deposition current collector

Significantly improved electrochemical performance of the commercial lithium titanate (Li4Ti5O12) achieved by using a novel current collector of cuprous iodide-modified copper foil

Preparation of CuO Nanorods for Lithium-Ion Battery Anodes by Supercritical Hydrothermal Reaction of Spent Acidic Etchant

Improve the Overall Performances of Lithium Ion Batteries by A Facile Method of Modifying the Surface of Cu Current Collector with Carbon