Abstract:A novel finding that the electrochemical performance of the commercial lithium titanate (Li 4 Ti 5 O 12 , LTO) can be significantly improved by using a novel current collector of CuI particles modified copper foil is reported for the first time in this work. Firstly, a large number of particles with well-defined shapes were prepared on the commercial copper foil surface via a very simple soaking process, in which the soaking solution contained only CuSO 4 , H 2 SO 4 and [Bmim]I. As indicated by the XRD and XPS measurements, the particles observed on the surface of the copper foil were identified as CuI particles. That is, CuI particles modified copper foils (denoted as CuI/Cu) were successfully prepared at room temperature. CuI/Cu prepared in the presence of 0.4, 0.6 and 0.8 g of [Bmim]I were nominated as CF (copper foil) a, b and c, respectively. Inconceivably, as compared to the conventional LTO electrode, the LTO electrodes assembled using the newly prepared CFs exhibited a significantly improved electrochemical performance, i.e., all as-prepared CFs showed an evident promoting effect on the electrochemical performance of the traditional LTO electrodes. For instance, the initial discharge capacity (DC) of the LTO electrode assembled using CF b (called electrode b) at 0.2 C was 307 mAh g −1 , which was about 1.86 times higher than that of the LTO electrode prepared using the conventional copper foil current collector (165 mAh g −1 ). Particularly, as the applied current rate was as high as 10 C, the DC value of electrode b (117 mAh g −1 ), even after 100 cycles, was still about 2.54 times that of the traditional LTO electrode (46 mAh g −1 ). In this preliminary work, a new method for preparing CuI particles was developed, along with a novel approach to significantly improve the electrochemical properties of the commercial LTO electrode. The method did not require any strong oxidants or reducing agents, nor did it demand any additional energy expenditure during the preparation of CuI particles. Moreover, the approach did not require any changes in the assembly procedure for the LTO electrodes being studied. This work was very meaningful for the development of the CuI-related research field as well as for the electrochemical performance improvement of LTO-based lithium-ion batteries (LIBs).

Significantly improved electrochemical performance of the commercial lithium titanate (Li4Ti5O12) achieved by using a novel current collector of cuprous iodide-modified copper foil

High-performances of Li4Ti5O12 anodes for lithium-ion batteries via modifying the Cu current collector through magnetron sputtering amorphous carbon

Calcining the mixture having lithium titanate (LTO) and CuBr in air to significantly boost the electrochemical performance of the commercial LTO

High-voltage Performance of LiCoO2 Cathode Studied by Single Particle Microelectrodes –influence of Surface Modification with TiO2

High-rate and Excellent-Cycle Performance Li4Ti5O12 Electrodes with 3D Porous Copper Foils As Current Collectors Fabricated Using a Femtosecond Laser Processing Strategy

Organic carbonized copper foil facilitates the performance of current collector for lithium-ion batteries

Structural Analysis and Electrochemical Studies of Carbon Coated Li4ti5o12 Particles Used As Anode for Lithium Ion Battery

Promoting Effect of Cobblestone-shaped CuI Nanoparticles Immobilized on the Copper Foil Surface on the Electrochemical Performance of the Conventional Graphite Electrode

Improve the Overall Performances of Lithium Ion Batteries by A Facile Method of Modifying the Surface of Cu Current Collector with Carbon

Phytic-Acid-Modified Copper Foil as a Current Collector for Lithium-Ion Batteries

Preparation of the Porous Copper Foil Current Collector for High-Performance Lithium-Ion Batteries by Electro-Codeposition: Effect of Stirring Speed

Elaborate strategy for preparing Li4Ti5O12-based anode materials with significantly improved lithium storage: TiO2 nanodots in-situ decoration and hierarchical structure construction

Lithiophilic Cu3Sn Modified Cu Foil as Current Collector for Stable Lithium Metal Anodes

Development of a Lightweight LTO/Cu Electrode as a Flexible Anode via Etching Process for Lithium-Ion Batteries

Microcrystalline copper foil as a high performance collector for lithium-ion batteries

A facile method to fabricate lightweight copper coated polyimide film current collectors for lithium-ion batteries

Large‐Scale Modification of Commercial Copper Foil with Lithiophilic Metal Layer for Li Metal Battery

One-stone, two birds: One step regeneration of discarded copper foil in zinc battery for dendrite-free lithium deposition current collector

Growing Cuprite Nanoparticles on Copper Current Collector Toward Uniform Li Deposition for Anode-Free Lithium Batteries

Advanced electrochemical performance of Li4Ti5O12-based materials for lithium-ion battery: Synergistic effect of doping and compositing

<i>In situ</i> coating of a lithiophilic interphase on a biporous Cu scaffold with vertical microchannels for dendrite-free Li metal batteries