Abstract:The evolution of surface morphologies of films prepared by ion-based deposition techniques has been investigated by atomic force microscopy. Two deposition processes, filtered arc deposition (FAD) and ion-beam-assisted deposition, where low-energy (<100 eV) ion irradiation and high-energy (several tens of keV) ion-beam bombardment concurrent with film growth were involved, respectively, have been employed to prepare TiN and Al films. Comparative studies on the effect of energetic ions on the development of topography have been performed between the low-ion-energy regime and high-ion-energy regime. In addition, the relationship between topography and mechanical properties of thin films has been revealed, by involving thin films prepared by thermal evaporation deposition (TED), where almost all depositing particles are neutral. In the images of the TED TiN and Al films, a large number of porous and deep boundaries between columnar grains was observed, suggesting a very rough and loose surface. In contrast, the FAD films exhibited much denser surface morphologies, although still columnar. The root-mean-square roughness of the FAD films was less than 1 Å. Hardness test and optical parameter measurement indicated that the FAD films were much harder and, in the case of optical films, much more transparent than the TED films, which was considered to arise from the denser surface morphologies rather than crystallization of the films. The high density and super smoothness of the FAD films, and the resultant mechanical and optical properties superior to those of the TED films, were attributed to the enhancement of surface migration of the deposited adatoms in the FAD process, which could provide intensive low-energy ion irradiation during film growth. As for topography modification by high-energy ion-beam bombardment concurrent with film growth, in addition to the increase of surface diffusion due to elastic collision and thermal spikes, physical sputtering must be considered while explaining the development of the film topography. Both surface migration enhancement and sputtering played important roles in the case of high-energy heavy-ion-beam bombardment, under which condition surface morphology characterized by dense columns with larger dimension and deep clean boundaries was formed. However, under high-energy light-ion-beam bombardment, the sputtering was dominant, and the variation of sputtering coefficient with position on the surface of growing film led to the formation of cones.

Exploring the Effect on the Columnar Structure and Porosity of the Synthesized Be Films by Oblique Angle Deposition in Magnetron Sputtering

Effect of deposition angle on the deposition rate, microstructure, electrical and optical properties of magnetron sputtered ZrB 2 thin films

Atomic Force Microscopy Study on Topography of Films Produced by Ion-Based Techniques

Influence of the Incident Flux Angles on the Structures and Properties of Magnetron Sputtered MoS2films

Effect of the Monomer TEOS Flow Rate on the Formation of Silicon Dioxide Films by Nonequilibrium,atmospheric Pressure Plasma Jet

Growth Mechanisms and the Effects of Deposition Parameters on the Structure and Properties of High Entropy Film by Magnetron Sputtering

Influence of Sputtering Pressure on the Micro-Topography of Sputtered Cu/Si Films: Integrated Multiscale Simulation

Effect of substrate-tilting angle-dependent grain growth and columnar growth in ZnO film deposited using radio frequency (RF) magnetron sputtering method

Effect of Sputtering Parameters on Film Composition, Crystal Structure, and Coercivity of SmCo Based Films Deposited on Si （100） Substrates

Growth dynamics of nanocolumnar thin films deposited by magnetron sputtering at oblique angles

Structure evolution from nanocolumns to nanoporous of nitrogen doped amorphous carbon films deposited by magnetron sputtering

Effects of Incident Angle on Microstructure of Ni Thin Film Deposited by PVD

Influence of Sputtering Power and Gas Pressure on the Preparation of Tungsten Films by DC Magnetron Sputtering

On the Pressure Effect in Energetic Deposition of Cu Thin Films by Modulated Pulsed Power Magnetron Sputtering: A Global Plasma Model and Experiments

Modelling of an obliquely deposited thin film in three dimensions by kinetic Monte Carlo method

Scaling Behaviors of Surface Roughening of Cu Thin Films Deposited by Oblique Angle Deposition

Investigation using Monte-Carlo codes simulations for the impact of temperatures and high pressures on thin films quality

Effects of Deposition Parameters on Microstructure of Magnetron Sputtered Ti Films and the Following Anodization

Effect of Deposition Pressure on Microstructure and Tribological Behavior of MoS X /mos X -Mo Nanoscale Multi-Layer Films

Analyses of Plasma Reactive Sputter Deposition of CN X Films by OES

Effect of the Deposition Parameters on the Mechanical Properties of Ti-B-C Films Deposited by Magnetron Sputtering