Abstract:In order to prepare cobalt-free cemented carbide by liquid phase sintering, various contents of Al2O3-ZrO2 by eutectic ratio were utilized as binders for tungsten carbides. The effects of Al2O3-ZrO2 content on the densification, microstructure, mechanical properties, and interfacial characteristics of these binderless tungsten carbides were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy, and mechanical properties tests. The fully dense WC toughened by Al2O3-ZrO2 composite powders could be consolidated through spark plasma sintering at 1600 degrees C. The results indicated that a small amount of eutectic Al2O3-ZrO2 binder phase (up to 3 wt%) would aggregate, increasing the contact chance of WC particles and eventually leading to abnormal growth of WC grains. When the Al2O3-ZrO2 content increases to 6.0 wt%, the abnormal growth of WC particles was inhibited by the pinning effect of the well-distributed second phase. The mean grain size of WC decreased with the increasing amount of Al2O3-ZrO2 content, while the mean grain size of Al2O3-ZrO2 colony increased. The temperature corresponding to the maximum shrinkage rate of densification process decreased with increasing Al2O3-ZrO2 content. In general, with the increase of the eutectic ceramic content, the hardness of the composite decreased and the indentation fracture toughness increased. The toughening mechanisms include crack deflection, crack bridging and t- to m-ZrO2 phase transformation toughening. The WC-Al2O3-ZrO2 composites show maximum toughness of approximately 10.5 MPa m(1/2) and hardness value of 22.29 GPa, respectively.

Synergistic strengthening and toughening of oscillatory pressure sintered WC-ZrO2-Al2O3 ceramics

Synergistic Toughening Effect of SiC Whiskers and Particles in ZrO2–Al2O3–SiC Ceramics

Improved comprehensive mechanical properties of oscillatory pressure sintered WC–ZrO2–Al2O3 ceramics with VC/Cr3C2 addition

Fabrication and Mechanical Properties of ZrO2–Al2O3–SiC(w) Composites by Oscillatory Pressure Sintering

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO2–Al2O3-SiCp ceramics

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics

Enhancing Hardness and Toughness of WC Simultaneously by Dispersed ZrO2

Microstructure and mechanical properties of oscillatory pressure sintered WC ceramics with different carbon sources

Microstructure and Characterization of Wc-2.8 Wt% Al2o3-6.8 Wt% Zro2 Composites Produced by Spark Plasma Sintering

Microstructural evolution and mechanical properties of ZrO<sub>2</sub> (3Y)-Al<sub>2</sub>O<sub>3</sub>-SiC(<sub>w</sub>) ceramics under oscillatory pressure sintering

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Toughening Cemented Carbides by Phase Transformation of Zirconia

Densification, microstructure and mechanical properties of ZrB2–SiCw ceramic composites

Zirconia Ceramics Consolidated by Oscillatory Pressure Sintering and Subsequent Carburization

Ultrafine‐grained WC‐based Ceramics Prepared Via Two‐step Oscillatory Pressure Sintering

Fabrication of ZrO2 whisker modified ZrO2 ceramics by oscillatory pressure sintering

Enhanced Mechanical Properties, Thermal Shock Resistance and Oxidation Resistance of Si2BC3N Ceramics with Zr-Al Addition

Effects of Al2O3–ZrO2 Content on the Densification, Microstructure, and Mechanical Properties of Cemented Tungsten Carbides

Microstructure and mechanical properties of ZTA fabricated by liquid phase sintering

In-situ Elongated Aluminium Borate Grains Toughening WC- 1.87 Wt % Al2O3- 4.13 Wt % ZrO2 Composite Via Spark Plasma Sintering

Preparation and Mechanical Properties of Fine Grain Al2O3-ZrO2 Composite Ceramics