Abstract:Pyrometallurgical processes have been widely recognised as the preferred technology for E-scrap recycling, and E-scrap smelting is usually accompanied by the formation of high-Al2O3-content slag. However, this slag can cause problems, such as refractory wear and even accelerated failure. Therefore, the corrosion mechanism of magnesia-chrome and alumina-chrome refractories in contact with FeOx-SiO2-CaO-Al2O3 smelting slag was experimentally studied in the range of 1300-1400 degrees C, in air (p(O2) = 0.21 atm) and at p(O2) = 10 atm. The results showed that refractory-component dissolution and new phases formation were the major causes of refractory degradation. The dissolution of the refractory components increased along with both increasing temperature and decreasing Al2O3 concentration in the initial slag. When decreasing the p(O2), the dissolution of MgO and Al2O3 into the slag slowed down. New phases such as forsterite, anorthite, and spinel were detected at the interface between the slag and the bulk refractory. The formation of forsterite accelerated the refractory wear, whereas the newly formed (MgO,FeO)center dot(Cr2O3,Fe2O3,Al2O3) spinel phase acted as a protective layer against further corrosion. A lower Al2O3 concentration in the slag and a higher smelting temperature both densified the formed spinel layer. Additionally, a high oxygen partial pressure was beneficial to the formation of spinel in the magnesiachrome refractory corrosion experiments. However, a low oxygen partial pressure was favourable for the formation of spinel on the surface of the alumina-chrome refractory materials. This study provides useful information for designing refractory materials and optimizing the processing parameters of E-scrap smelting.

Alumina-enhanced Valorization of Ferronickel Slag into Refractory Materials under Microwave Irradiation

From ferronickel slag to value-added refractory materials: A microwave sintering strategy

Chromium-promoted preparation of forsterite refractory materials from ferronickel slag by microwave sintering

Effects of Sintering Temperature and Time on Preparation of Refractory Materials from Ferronickel Slag Under Microwave Irradiation

Facile Route for Preparing Refractory Materials from Ferronickel Slag with Addition of Magnesia

Valorization of Ferronickel Slag into Refractory Materials: Effect of Sintering Temperature

Preparation of Refractory Materials from Ferronickel Slag

Promoting Spinel Formation and Growth for Preparation of Refractory Materials from Ferronickel Slag

Chromium: A Double-Edged Sword in Preparation of Refractory Materials from Ferronickel Slag

Preparation of Refractory Materials from Electric Furnace Ferronickel Slag and Blast Furnace Ferronickel Slag: A Comparison

Assessing Magnesia Effect on Preparing Refractory Materials from Ferrochromium Slag

Preparation of Magnesium Aluminum Ferrite Spinel by Microwave Sintering

Thermodynamic Characteristics of Ferronickel Slag Sintered in the Presence of Magnesia

Preparation of Refractory Materials by Co-sintering of Ferronickel Slag and Ferrochromium Slag: Thermodynamic Analysis

Significant improvement of slag corrosion resistance and thermal shock resistance of corundum‐based dry vibratable refractory by addition of Fe–Si 3 N 4

Synergistic preparation of forsterite‐spinel refractory materials from ferronickel slag and ferrochromium slag

Alumina Recovery from Red Mud with High Iron by Sintering Process

Preparation and characterization of low-cost refractories for aluminum-melting-furnace linings from ferrotitanium slag

Development of an Ultra-Low Carbon MgO Refractory Doped with α-Al2O3 Nanoparticles for the Steelmaking Industry: A Microstructural and Thermo-Mechanical Study

Corrosion Mechanism of Magnesia-Chrome and Alumina-Chrome Refractories in E-scrap Smelting

Co-utilization of ferronickel slag and fly ash cenosphere for production of superior thermal insulation materials