Abstract:TiAl intermetallic alloys have attracted considerable attention in aerospace applications over the last few decades owing to their low density and superior mechanical properties at high temperatures. However, these alloys are also known as difficult-to-machine materials that hinder efficient manufacturing. This study presents a systematic investigation on the machinability of TiAl alloys with three types of microstructures obtained by different heat treatment parameters. These were classified as near-gamma (NG), duplex (DP), and fully lamellar (FL). The machinability was evaluated based on the cutting forces and machined surface roughness. The material with α2/γ lamellar structures (FL) exhibited the lowest cutting force (3.21 N). However, produced a rougher surface (80 nm Ra) as compared to the NG microstructure (4.69 N and 47 nm Ra). Electron backscattering diffraction (EBSD) evaluation of the primary deformation zone in the cutting chips revealed that insufficient heat energy was converted from plastic deformation for recrystallization or β+γ→α2 phase transformation to occur. This indicated that the deformation mechanisms were significantly dependent upon the plasticity. The NG microstructure demonstrated a higher degree of plasticity in the primary deformation zone, which was attributed to the combined effect of super-dislocation decomposition, ordinary dislocation slip, and refined mechanical twins with preferred orientation along the < 11 2 ¯ > {111} crystallographic orientation. Conversely, the FL microstructure exhibited brittleness during chip formation due to the weak bonding force between hexagonal α2 and tetragonal γ phases that led to preferential micro-cracking along each interface. Reducing the crystal orientation is conductive for improving machined surface quality. The notion of enhanced brittleness to explain the reduction in cutting forces due to the dissipation of energy through fracture was supported with numerical simulations. Microscopic evaluation was used to understand the deformation differences of the equiaxed γ grain and α2/γ lamellar microstructure during micro-cutting. Additionally, enhanced the understanding of the deformation mechanism of these multi-phase alloys.

Microstructure Formation and Tailoring of the Intermetallic TiAl Alloy Produced by Direct Laser Deposition

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Evolution of microstructure and mechanical property of Ti-47Al-2Cr-2Nb intermetallic alloy by laser direct energy deposition: From a single-track, thin-wall to bulk

Microstructure characteristics of a γ single-phase Ti-55Al-7.5Nb alloy fabricated via additive manufacturing

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Investigation of Ti2AlNb-Added TiAl Composite Prepared by Direct Laser Deposition

Influence of Interface on Microstructure and Mechanical Properties of Laser-Direct Energy Deposited Ti60 Alloy

Formation Mechanism of Dilute Region and Microstructure Evolution in Laser Solid Forming TA15/Ti2AlNb Dual Alloy

Effect of TiB 2 on the microstructure and mechanical properties of TiAl alloy produced by laser direct energy deposition

Investigation of the Influence of Process Parameters on Crack Formation and Mechanisms in Ti-48Al-2Cr-2Nb Alloy via Laser Directed Energy Deposition

Direct laser fabricated in situ TiC particulate reinforced Ni30Al20Fe intermetallic matrix composite

Additive manufacturing of Ti-6Al-4V alloy by micro-laser metal wire deposition with pulsed wave emission: processability and microstructure formation

Phase transformation mechanism and mechanical properties of Ti-45Al-8Nb alloy prepared by directed laser deposition

Optimization of Processing Parameters and Microstructure Evolution of (TiB+La 2 O 3 )/Ti6Al4V Manufactured by Laser Melting Deposition

Study of microstructure and compressive strength of a novel Ti-0.75Al-9.5V alloys manufactured by laser deposition melting

Microstructure of a Ti–50 Wt% Ta Alloy Produced Via Laser Powder Bed Fusion

Microstructure, Mechanical, and Tribological Properties of Nb-Doped TiAl Alloys Fabricated via Laser Metal Deposition

Microstructural modulation of TiAl alloys for controlling ultra-precision machinability