Abstract:Selective laser melting (SLM) technology was employed for the additive manufacturing of Ti-5Al-2.5Sn alpha titanium alloy in this work and the influences of laser energy input on densification behavior, microstructure evolution and mechanical performances of the as-deposited products were investigated. It was found that the relatively high volumetric energy densities (VEDs) of 167-417 J/mm(3) resulted in large quantities of keyhole-induced spherical pores whereas the relatively low VEDs of 51-83 J/mm(3) led to notable lack-of-fusion defects. At the proper VED of 125 J/mm(3), highly densifled products with internal porosity of merely 0.05% were obtained. At the relatively high VEDs of 167-417 J/mm(3), as-built samples presented duplex microstructures composed of acicular alpha' martensites and bulk alpha(M) massive grains. In contrast, overwhelmingly martensitic microstructures were formed at lower VEDs of 51-125 J/mm(3). The martensitic microstructure exhibited a unique hierarchical feature, which could be explained using the theory of athermal martensitic transformation kinetics. With the decrease of VED from 417 J/mm(3), the average size of alpha' needles increased first, then came to its plateau at the VEDs of 167-208 J/mm(3), and decreased again at the VEDs of 51-167 J/mm(3). At the VEDs of 167-417 J/mm(3), the formation of spherical pores and bulk alpha(M) grains resulted in relatively poor tensile properties. At the VEDs of 51-83 J/mm(3), the formation of lack-of-fusion defects masked the enhanced fine-grain strengthening effect provided by the much refined alpha' needles and the decrease in the fraction of bulk alpha(M), thus also leading to very limited tensile properties. At the proper VED of 125 J/mm(3), as-built tensile properties reached to their peak with ultimate tensile strength of 1173 MPa, yield strength of 1061 MPa, and elongation of 7.7%. This can be attributed to the high densification degree, the almost complete vanish of bulk alpha(M) grains, and the moderate size of alpha' needles. (C) 2018 Elsevier B.V. All rights reserved.

Study of microstructure and compressive strength of a novel Ti-0.75Al-9.5V alloys manufactured by laser deposition melting

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

The Microstructure and Mechanical Behaviors of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si Alloy Produced by Laser Melting Deposition

Microstructure and mechanical properties of laser melting deposited γ-TiAl intermetallic alloys

Microstructure And Tensile Properties Of Laser Melting Deposited Ti-5al-5mo-5v-1cr-1fe Near Beta Titanium Alloy

Microstructure and mechanical properties of a newly developed Ti-6Al-2Mo-2Sn-2Zr-2Cr-2V alloy fabricated by laser directed energy deposition

Anisotropic Tensile Behavior of Ti-47Al-2Cr-2Nb Alloy Fabricated by Direct Laser Deposition

Microstructure Evolution and Mechanical Behavior of Al–Li Alloy Fabricated by Laser Melting Deposition Technique

Microstructure and mechanical properties of laser additive manufactured novel titanium alloy after heat treatment

Microstructure and Mechanical Properties of As-Deposited and Heat Treated Ti–5Al–5Mo–5V–3Cr–1Zr (Ti-55531) Alloy Fabricated by Laser Melting Deposition

Chemical, microstructure, and mechanical property of TiAl alloys produced by high-power direct laser deposition

Microstructure and Mechanical Properties of a Novel Al-Mg-Sc-Ti Alloy Fabricated by Laser Powder Bed Fusion

Microstructural evolution and mechanical properties of laser melting deposited Ti–6.5Al–3.5Mo–1.5Zr–0.3Si titanium alloy

Microstructure and Properties of a Novel Titanium Alloy Ti-6Al-2V-1.5Mo-0.5Zr-0.3Si Manufactured by Laser Additive Manufacturing

Effect of Α Phase on High-Strain Rate Deformation Behavior of Laser Melting Deposited Ti-6.5Al-1Mo-1V-2Zr Titanium Alloy

Densification Behavior, Microstructure Evolution, and Mechanical Performances of Selective Laser Melted Ti-5Al-2.5Sn Α Titanium Alloy: Effect of Laser Energy Input

Microstructure and Mechanical Properties of Laser Metal Deposited Ti6Al4V Alloy with Near Equiaxed Β Grain Structure

Effect of Processing Parameters on Formability, Microstructure, and Micro-Hardness of a Novel Laser Additive Manufactured Ti-6.38Al-3.87V-2.43Mo Alloy

Effect of thermal exposure on microstructure and tensile properties of laser deposited Ti60A alloy