Abstract:The challenge of fabrication large-scale laser melting deposited titanium alloy (LLMDT) components was high residual stress, warpage deformation, and even fracture during long-time continuous deposition. To address this challenge, a method named discrete deposition and segregated heat-treatment (DDSH) was used to fabricate the LLMDT components and its effect on the macro- and microstructure, and tensile properties have been systematically studied. The results showed the macrostructure of the DDSH interface region showed columnar grains due to its higher thermal gradient and lower solidification rate than them in other LLMDT parts with columnar grains and equiaxed grains. The microstructure in the whole LLMDT components consisted of ultrafine basket-weave microstructure. The average width of the α lamellae in the DDSH interface region and other LLMDT parts was 0.38–0.424 μm and 0.477–0.54 μm, respectively. The average width of α lamellae was finer in the DDSH interface region than that in the other LLMDT parts owing to its higher thermal gradient and higher cooling rate compared with the other LLMDT parts. For the LLMDT components in different directions with the same region, the UTS and the YS in the H-sample were slightly higher than those in the V-sample, while the EL in the H-sample was lower than those in the V-sample. The anisotropic ductility was owing to the continuous grain boundary exhibited different fracture mechanisms under different directions with loading stress. For the LLMD components in different regions with the same direction, the highest fluctuation ratio of the UTS, the highest fluctuation ratio of the YS, and the highest fluctuation ratio of the EL was 0.012%, 0.08%, and 0.145%, respectively. The reason was the average with of the α lamellae in the whole LLMDT components showed a little difference.

Strengthening Effect in Laser Metal Deposited Ti6Al4V Alloy Via Layer-by-layer Ultrasonic Impact Treatment

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Simultaneous improvement of strength and elongation of laser melting deposited Ti-6Al-4V titanium alloy through three-stage heat treatment

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Microstructure and Mechanical Properties of An Ultrahigh-strength Titanium alloy Ti-4.5Al-5Mo-5V-6Cr-1Nb Prepared Using Laser Directed Energy Deposition and Forging: A Comparative Study

Study of microstructure and compressive strength of a novel Ti-0.75Al-9.5V alloys manufactured by laser deposition melting

In-situ study of tensile behavior of Ti/Al laminated metal composites fabricated via ultrasonic additive manufacturing

Laser Metal Deposition of Ti6Al4V—A Brief Review

Influence of laser treatment on the microstructural evolution and performance of Ti65 alloy

Effect of heat treatment on microstructure and mechanical properties of laser-deposited Ti65 near-alpha titanium alloy

Microstructure and mechanical properties of a newly developed Ti-6Al-2Mo-2Sn-2Zr-2Cr-2V alloy fabricated by laser directed energy deposition

Enhancing Hardness and Wear Performance of Laser Additive Manufactured Ti6Al4V Alloy Through Achieving Ultrafine Microstructure

Effect of discrete deposition and segregated heat-treatment on the macro- and microstructure, and tensile properties of large-scale titanium alloy components by laser melting deposition

Effect of ultrasonic amplitude on interfacial characteristics and mechanical properties of Ti/Al laminated metal composites fabricated by ultrasonic additive manufacturing

Effect of Ultrasonic‐Assisted Treatment on Microstructure and Mechanical Properties of Laser Deposition Repairing AlSi7Mg Alloy

Strengthening layer with nano-twins in titanium alloy induced by laser surface re-melting: Mechanism of high strength and ductility

Influence mechanism of microstructure variation on mechanical properties of laser melting deposition Ti–6Al–4V alloy under electroshocking treatment

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties

Effects of Heat Treatments on Microstructures and Mechanical Properties of Ti6Al4V Alloy Produced by Laser Solid Forming