Abstract:Successful preparation of photopolymerizable ceramic slurries using non-oxide ceramics and their 3D printing is highly challenging as the ceramic powders often possess high UV-light absorbance. Even though pre-oxidation of the powders could improve the slurry printability, the residual oxygen element in the material would eventually deteriorate the material purity and performance. In this study, a separated redox route (pre-oxidation, 3D printing and carbothermal reduction) was proposed to overcome these challenges. SiC ceramic powder was pre-oxidized into SiC@SiO2 core-shell form to lower the UV-light absorbance. It was found that the ultraviolet (UV) light absorbance value of SiC powder at 405 nm decreased 20% from 0.357 to 0.284 after pre-oxidation process. The UV-light penetration depth of SiC@SiO2 ceramic slurries at 40 similar to 55 vol% solid loading ranging from 14.81 to 12.82 mu m, which surpassed two times that for 40 vol% raw SiC ceramic slurry. Different-shaped structures of SiC@SiO2/resin green ceramic bodies were successfully fabricated by vat photopolymerization 3D printing. The oxygen element resided was then eliminated by carbothermal reduction to avoid detriment of SiO2 to the mechanical performance of the SiC ceramics. Phenolic epoxy acrylate resin with 14 wt% pyrolytic carbon (PyC) yield was chosen as the carbon source and thus the SiC@SiO2/resin green body pyrolyzed into SiC@SiO2/PyC ceramics after 1200 degrees C. It was found that after the heating temperature was further raised to 1600 degrees C, most of the pre-introduced SiO2 shells on the surface of SiC particles were in situ transformed into SiC nanowires through carbothermal reduction reaction between SiO2 and PyC, and the content of oxygen element in the ceramic matrix sharply dropped from 20.21% to 2.08%. The results demonstrated that through the proposed redox route, the photopolymerization-related issues including high UV-light absorbance and pre-oxidation-induced impurity for 3D printing of SiC ceramic slurries can be tackled. Finally, high purity porous SiCnw/SiC ceramic components with different structures were produced. This study provides a promising route for the preparation and 3D printing of photopolymerization ceramic slurries using non-oxide ceramics possessing high UV-light absorbance.

Fabrication of SiOC Ceramic with Cellular Structure Via UV-Assisted Direct Ink Writing

3D Printing of SiC Ceramic: Direct Ink Writing with a Solution of Preceramic Polymers

Direct Ink Writing of Continuous SiO 2 Fiber Reinforced Wave-Transparent Ceramics

Fabrication of SiOC Ceramic Microparts and Patterned Structures from Polysiloxanes via Liquid Cast and Pyrolysis

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Liquid Silicone Rubber with Uniformly Dispersed Nanosized Silica for the Preparation of SiOC Ceramics

Preparation of complex SiOC ceramics by a novel photocurable precursor with liquid crystal display ( LCD) 3D printing technology

Construction of EG/SiOC@C porous structure by direct ink writing and in-situ vapor self - Deposition to enhance microwave absorption

Curing performance and print accuracy of oxidized SiC ceramic via vat photopolymerization

UV-assisted direct ink writing of Si3N4/SiC preceramic polymer suspensions

3D Printing and in Situ Transformation of SiCnw/SiC Structures

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

Microstructure and mechanical properties of continuous carbon fiber-reinforced SiC ceramic composite fabricated by direct ink writing

SiCw/SiCp Reinforced 3D-Sic Ceramics Using Direct Ink Writing of Polycarbosilane-Based Solution: Microstructure, Composition and Mechanical Properties

UV-assisted Robotic Arm Freeforming of SiOC Ceramics from a Preceramic Polymer

Multiscale design and digital light processing preparation of high-strength SiOC ceramic metastructures for tuning microwave absorption properties

Fabrication and properties of SiO2f/SiO2 composite ceramic based on stereolithography technology

Fabrication of Si 2 N 2 O Ceramic Foam by Combination of Direct Ink Writing and Biological Foaming Technique

Silicon carbide whiskers reinforced SiOC ceramics through digital light processing 3D printing technology

Fabrication of macroscopic complicated-shaped bulk silicon oxycarbide ceramics from liquid polysiloxanes by crosslink-cast-pyrolysis

Vat photopolymerization 3D printing of polymer-derived SiOC ceramics with high precision and high strength