Abstract:In a previous work, an ink based on a preceramic polymer, SiC fillers, and chopped carbon fibers was proposed for the production of Ceramic Matrix Composite (CMC) structures by Direct Ink Writing (DIW) and subsequent pyrolysis. Thanks to the shear stresses generated at the nozzle tip during extrusion, carbon fibers can be aligned along the printing direction. Fumed silica was added to the ink in order to enhance its rheological properties; however, the printed structures still showed some deformation in the Z direction. In this work, a second ink was successfully developed to limit deformation and at the same time avoid the addition of fumed silica, which limited the potential temperature of application of the composites. Instead, the positive role of the preceramic polymer on the ink rheology was exploited by increasing its concentration in the ink. Rheological characterization carried out on both inks confirmed that they possessed Bingham shear thinning behavior and fast viscosity recovery. Single filaments with different diameters (~310 µm and ~460 µm) were produced with the latter ink by DIW and subsequent pyrolysis. Tested under a four-point flexural test, the filaments showed a mean flexural strength above 30 MPa, graceful failure, and fiber pull-out. The results of this work suggest that CMC components can effectively be fabricated via DIW of a preceramic ink with embedded short fibers; the preceramic polymer is able to provide the desired rheology for the process and to develop a dense matrix capable of incorporating both fibers and ceramic particles, whereas the fibers addition contributes to an increase of the fracture toughness of the material and to the development of a graceful failure mode.

Direct Ink Writing of Continuous SiO 2 Fiber Reinforced Wave-Transparent Ceramics

Microstructure and mechanical properties of continuous carbon fiber-reinforced SiC ceramic composite fabricated by direct ink writing

Continuous carbon fiber reinforced ZrB2-SiC composites fabricated by direct ink writing combined with low-temperature hot-pressing

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

First Printing of Continuous Fibers into Ceramics

Fabrication of SiOC Ceramic with Cellular Structure Via UV-Assisted Direct Ink Writing

3D Printing of SiC Ceramic: Direct Ink Writing with a Solution of Preceramic Polymers

Mechanical and Dielectric Properties of 3D Printed Highly Porous Ceramics Fabricated Via Stable and Durable Gel Ink

Direct Ink Writing of Chopped Carbon Fibers Reinforced Polymer-derived SiC Composites with Low shrinkage and High Strength

Direct Ink Writing of Non-Sintered Ceramic with Biomimetic Cellular Structure

Fabrication of Broadband Wave-Transparent Si3N4 Ceramics with Octet-Truss Lattice Structure by Vat Photopolymerization 3D Printing Technology

Optimization and Characterization of Preceramic Inks for Direct Ink Writing of Ceramic Matrix Composite Structures

Thermally assisted extrusion-based 3D printing of continuous carbon fiber-reinforced SiC composites

Mechanical and dielectric properties of Si3N4/β-SiAlON composite ceramics fabricated by vat photopolymerization 3D printing technology

Fabrication of broadband wave-transparent Si 3 N 4 ceramics with octet-truss lattice structure by vat photopolymerization 3D printing technology

Mechanical and dielectric properties of porous and wave-transparent Si3N4-Si3N4 composite ceramics fabricated by 3D printing combined with chemical vapor infiltration

Mechanical and Dielectric Properties of Si3N4/(3-SiAlON Composite Ceramics Fabricated by Vat Photopolymerization 3D Printing Technology

SiCw/SiCp Reinforced 3D-Sic Ceramics Using Direct Ink Writing of Polycarbosilane-Based Solution: Microstructure, Composition and Mechanical Properties

Mechanical and Dielectric Properties of Direct Ink Writing Si2N2O Composites

Stereolithography of SiOC Polymer‐Derived Ceramics Filled with SiC Micronwhiskers