Abstract:Ultra‐highly porous and mechanically strong materials are made by tuning interfacial chemistry of the nanoparticle suspensions. The introduced ethanol assists the surfactant to be adsorbed onto the silica surface with enhanced efficiency. High energy of attachment of the nanoparticles improves the stability of the Pickering system. The strong interactions within the foam endow the green bodies with mechanical strengths as well. Highly porous foam ceramics exhibit broad prospects for multifunctional applications. With the facile Pickering‐based foaming technique, wet foams consisting of nanoparticles (NPs) may exhibit high strengths. However, they also experience linear shrinkages as high as 50% after drying and sintering process. Suitable solutions for improving this situation have not been found yet. This work develops a method for fabricating NP‐made foam ceramics by tuning the interfacial chemistry of this Pickering system. Trace amounts of ethanol are used to adjust the adsorbing behavior of surfactants on the silica surface to enhance the energy of attachment of the Pickering systems. Combined with the altered capillary forces, the linear shrinkages of the foam ceramic are considerably lowered. The pore wall of the obtained foam ceramics can be tuned to either closed or open due to the "coffee ring" effect by adjusting the solid content and sintering temperature. The samples present high thermal insulating properties and high mechanical strength even the unsintered ones, which also show good stability in liquid environments. Combined with the direct ink writing (DIW) technique, these freely shaped materials with tunable pore structures can be readily exploited in tissue scaffolds, catalyst carriers, thermal insulators, battery electrodes, and liquid/gas filtration, etc.

Fabrication of Si 2 N 2 O Ceramic Foam by Combination of Direct Ink Writing and Biological Foaming Technique

Mechanical and Dielectric Properties of Direct Ink Writing Si2N2O Composites

Preparation of Si 3N 4 foam ceramics with nest-like cell structure by particle-stabilized foams

Direct ink writing of Si<sub>2</sub>N<sub>2</sub>O porous ceramic strengthened by directional -Si<sub>3</sub>N<sub>4</sub> grains

Mechanical and Dielectric Properties of 3D Printed Highly Porous Ceramics Fabricated Via Stable and Durable Gel Ink

Fabrication and properties of Si2N2O-Si3N4 ceramics via direct ink writing and low-temperature sintering

3D Printing of Porous Si2N2O Ceramics Based on Strengthened Green Bodies Fabricated Via Strong Colloidal Gel

Fabrication of Clay Foam Ceramics Using Silicon Carbide and Ferric Oxide as Foaming Agents

Direct ink writing of Si2N2O porous ceramic strengthened by directional β-Si3N4 grains

Fabrication of Pure SiC Ceramic Foams Using SiO2 As a Foaming Agent Via High-Temperature Recrystallization

Pore Structure Control of Si3n4 Ceramics Based on Particle-Stabilized Foams

A Novel Method of Strong and Tough Si3N4 Ceramic from the Particle‐stabilized Foam

Study on particle-stabilized Si3N4 ceramic foams

3D Printable Ultra‐Highly Porous and Mechanically Strong Foam Materials for Multiple Applications

Preparation of Si3N4 Foam Ceramics Using Short-Chain Amphiphile

Rheology of organics-free aqueous ceramic suspensions for additive manufacturing of dense silicon nitride ceramics

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

Fabrication of hierarchically porous Si3N4 foam ceramics with stamen-like cell structure

In Situ Synthesis of Three-Dimensional Nanofiber-Knitted Ceramic Foams Via Reactive Sintering Silicon Foams

Effect of Foaming Pressure on the Properties of Porous Si3n4 Ceramic Fabricated by A Technique Combining Foaming and Pressureless Sintering

3D printing boehmite gel foams into lightweight porous ceramics with hierarchical pore structure