Abstract:Digital light processing (DLP) 3D-printed Si3N4 ceramics, known for their exceptional performance, offer distinct advantages in meeting the high-strength and complex structural demands of industries such as aerospace, semiconductors, healthcare, automotive, energy, and machinery. However, due to Si3N4's strong chemical stability, low diffusion rate, low self-sintering ability, and high melting point, achieving densification under conventional sintering conditions is challenging. As a result, sintering additives are essential to promote the sintering process, lower the sintering temperature, improve densification, and enhance performance. In this study, 45 vol% Si3N4 slurries were prepared using DLP 3D printing technology, incorporating nine different combinations of sintering additives, including aluminum oxide (Al2O3), yttrium oxide (Y2O3), and aluminum nitride (AlN), in various ratios with Si3N4. The slurries were then sintered at 1800 °C for 2 h under a 1 MPa N2 atmosphere. Additionally, the phase composition, microstructure, grain distribution, and crack propagation of the materials. The results showed that a Si3N4 to Al2O3 and Y2O3 ratio of 95:2.5:2.5 produced elongated β-Si3N4 grain structures and enhanced density, achieving a maximum Vickers hardness of 12.88 ± 0.52 GPa. Additionally, the synergistic toughening effect of the rod-like β-Si3N4 grains and sintering aids significantly improved the fracture toughness of the Si3N4 ceramic matrix, with a flexural strength of 540.63 ± 10.05 MPa and a fracture toughness of 4.92 ± 0.07 MPa·m1/2. This study lays the foundation for the future application of 3D-printed Si3N4 ceramics, optimization of sintering aid combinations at different ratios, and performance enhancement in extreme environments.

Rheology of organics-free aqueous ceramic suspensions for additive manufacturing of dense silicon nitride ceramics

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Large-size Si 3 N 4 ceramic fabricated by additive manufacturing using long-term stable hydrogel-based suspensions

Fabrication and properties of Si2N2O-Si3N4 ceramics via direct ink writing and low-temperature sintering

Surface Characterization of Silicon Nitride Powder and Electrokinetic Behavior of Its Aqueous Suspension

Microstructure, Mechanical and Dielectric Properties of Highly Porous Silicon Nitride Ceramics Produced by a New Water-Based Freeze Casting

Effect of Acid Cleaning and Calcination on Rheological Properties of Concentrated Aqueous Suspensions of Silicon Nitride Powder

Formation mechanism of stereolithography of Si3N4 slurry using silane coupling agent as modifier and dispersant

Preparation and optimization of silicon nitride slurries for digital light processing

Si 3 N 4 slurry with high solid phase, low viscosity prepared via surface-oxidation and silane coupling agent modification hybrid method

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

Additive manufacturing of SiC-Sialon refractory with excellent properties by direct ink writing

Additive manufacturing of complexly shaped SiC with high density via extrusion-based technique – Effects of slurry thixotropic behavior and 3D printing parameters

3D printing of ceramics with controllable green‐body configuration assisted by the polyvinyl alcohol‐based physical gels

Fused Deposition Modeling of Si3N4 Ceramics: A Cost-Effective 3D-Printing Route for Dense and High Performance Non-Oxide Ceramic Materials

3D printing Si3N4-bonded SiC refractories fabricated using colloidal films-containing slurries based on non-spherical SiC and Si powders

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

Direct Coagulation Casting of Silicon Nitride Suspension Via a Dispersant Reaction Method

Densification mechanism of stereolithographical dense Si3N4 ceramics with CeO2 as sintering additive by field assisted sintering

Linking Rheology and Printability for Dense and Strong Ceramics by Direct Ink Writing

Si 3 N 4 ceramics with embedded microchannel structures fabricated by high-precision additive manufacturing based on computational fluid dynamics simulations