Abstract:The high refractive index, high absorbance, and low sintering activity of SiC powders pose challenges in achieving sufficient curing depth of SiC slurries and achieving densification of SiC ceramics. Hence, the preparation of high-strength SiC ceramics by vat photopolymerization is a challenge. This study proposes a strategy of particle surface oxidation modification and particle gradation to address this difficulty. Specifically, the surface of micron and submicron SiC particles is oxidatively modified to enhance the curing depth of SiC slurry, and the gradation of these particles is optimized to improve the sintering activity of the SiC particle system. The percentage of oxidized micron and submicron SiC particles is carefully adjusted to meet the requirements of both vat photopolymerization preparation and sintering. It found that increasing the percentage of sub-micron particles in the particle grade system had a negative impact on the rheological and curing properties of the slurry but contributed to the stability of the slurry and the performance of the sintered ceramic parts. Ensuring that the percentage of sub-micron particles reaches 50% or higher and reducing direct contact between micron particles to form sintered necks are two key conditions for the preparation of high-strength SiC ceramics. Additionally, it found that interlayer bonding location is the pore defects concentrated in the sintered ceramic parts, providing direction for further optimization of ceramic properties. By implementing the oxidation modification and particle gradation optimization strategy, the densification and three-point flexural strength of SiC ceramic parts were improved significantly. The relative density and three-point flexural strength of SiC increased from 65.7 ± 5.3% to 86.8 ± 3.7% and from 75.0 ± 2.1 to 170.9 ± 11.6MPa, respectively. This approach provides a simple and effective method to prepare high-strength SiC ceramics by vat photopolymerization.

Liquid Silicone Rubber with Uniformly Dispersed Nanosized Silica for the Preparation of SiOC Ceramics

Synthetic strategies of high-inorganic-content thermoplastic SiO2 based composites

Polymer-derived SiOC ceramics: A potential catalyst support controlled by the sintering temperature and carbon content

Fabrication of SiOC Ceramic with Cellular Structure Via UV-Assisted Direct Ink Writing

Fabrication of SiOC Ceramic Microparts and Patterned Structures from Polysiloxanes via Liquid Cast and Pyrolysis

Pyrolytic Transformation of Liquid Precursors to Shaped Bulk Ceramics

Synthesis of Ordered Mesoporous Silicon Oxycarbide Monoliths Via Preceramic Polymer Nanocasting

Effect of Solvent in Preparation of SiOC Bulk Ceramics

In-situ Growth of SiOC Fibers in SiOC Ceramic to Prepare SiOC/SiOC_f Composites with Polysiloxane via Pre-mixing of Iron Chloride

Preparation of Amorphous SiOC Ceramic Powders through Precursor Polymer Pyrolysis

Fabrication of macroscopic complicated-shaped bulk silicon oxycarbide ceramics from liquid polysiloxanes by crosslink-cast-pyrolysis

Molecular Aggregation Strategy for Pore Generation in SiOC Ceramics Induced by the Conjugation Force of Phenyl

Sol-gel synthesis of preceramic polyphenylsilsesquioxane aerogels and their application toward monolithic porous SiOC ceramics

Additive Manufacturing of Silicon Oxycarbide Ceramics with Minimal Surface Structures

Effects of Different Polymer Precursors on the Characteristics of SiOC Bulk Ceramics

Sol-gel preparation of ZrO2–Li2Si2O5 ceramics and their sintering properties

A Pyrolysis Heating Rate Based Pressureless Method for Preparing Dense and Crack-Free Polymer-Derived Silicon Oxycarbide Bulk Ceramics

Morphology Design of Porous Si2N2O Ceramics via Silica Poly-Hollow Microspheres

In-situ Reaction Synthesis of Porous Si2N2O-Si3N4 Multiphase Ceramics with Low Dielectric Constant Via Silica Poly-Hollow Microspheres

Particle Surface Oxidation Modification and Particle Gradation Strategy for the Preparation of High-Strength SiC Ceramics Via Vat Photopolymerization

Fabrication of Al2O3‐SiO2 Ceramics Through Combined Selective Laser Sintering and SiO2‐sol Infiltration