Enhanced Production of Aromatics from Propane with a Temperature-Shifting Two-Stage Fluidized Bed Reactor.

Yifeng Yang,Yilin Hou,Zhaohui Chen,Huiqiu Wang,Yu Wang,Boyang Liu,Zhuoya Dong,Jun Gao,Ran Wei,Weizhong Qian

DOI: https://doi.org/10.1039/c9ra05420k

IF: 4.036

2019-01-01

RSC Advances

Abstract:High-yield production of aromatics from propane with a temperature shifting, two-stage fluidized bed reactor technology.

What problem does this paper attempt to address?

High-yield Production of Aromatics from Methanol Using a Temperature-Shifting Multi-Stage Fluidized Bed Reactor Technology

Zhaohui Chen,Yilin Hou,Wenlong Song,Dali Cai,Yifeng Yang,Yu Cui,Weizhong Qian

DOI: https://doi.org/10.1016/j.cej.2019.04.024

IF: 15.1

2019-01-01

Chemical Engineering Journal

Abstract:We propose a temperature-shifting three-stage fluidized bed reactor technology for the consecutive conversion of methanol and its intermediate products into aromatics. The first stage served the aromatization of methanol. The second stage served the aromatization of the intermediates of light paraffins and olefins. The third stage served the alkylation of residual olefins. The yield of the aromatics was relatively stable within 12 h in the exit of third stage and was 6-12% higher than that in the exit of first stage. The increased yield of aromatics was attributed to the effective transformation of intermediate products (C-2-C-5 hydrocarbons). The final alkenes/alkanes ratio dropped to only 0.03. The time-dependent yields of aromatics, olefins and paraffins were analyzed in detail based on the information of coke at different stages. The results provide insight into the consecutive conversion network of methanol into aromatics.
Thermodynamic Analysis of Propane Aromatization

P. Moghimpour Bijani,M. Sohrabi,S. Sahebdelfar

DOI: https://doi.org/10.1080/10916466.2012.678539

IF: 1.695

2014-04-08

Petroleum Science and Technology

Abstract:Chemical equilibria of propane aromatization under both unrestricted coke-formation and coke-free operating conditions were studied. In both cases, propane conversions were nearly complete. The aromatics selectivity was observed to be 46% at a temperature of 823 K (1 bar) under coke-free operating conditions. Application of hydrogen and steam as coke-removing agents was also studied. Under coke-free operation, the presence of low level of water in the feed favors propane methanation, whereas higher levels of water enhance propane steam reforming. Methane selectivity was found to attain a maximum at H2O/C3H8 molar ratio equal to 0.75 (823 K, 1 bar). The outcomes of the present study imply that the products selectivity has to be controlled kinetically and that the catalyst formulation should be aimed at minimization of coke formation and carbon-carbon bond breakage activity.

energy & fuels,engineering, chemical, petroleum
Mixing Effects on the Gas Flow and Mass Transfer in a Vertical Single Helical Ribbon Agitated Reactor for Propylene Polymerization

Ye Tianzhou,Sun Jingyuan,Huang Zhengliang,Yang Yao,Jiang Binbo,Wang Jingdai,Yang Yongrong

DOI: https://doi.org/10.1016/j.cej.2023.144492

IF: 15.1

2023-01-01

Chemical Engineering Journal

Abstract:The gas-solid vertical single helical ribbon agitated reactor is widely used in the polypropylene industry. The gas flow and mass transfer determine the heat transfer capacity and product quality. In this work, the pressure drop was measured below and above minimum fluidization velocity (umf). Then, the axial and radial dispersion coefficients (DL and DR) were estimated below umf by measuring the step residence time distribution and the stationary radial tracer profiles, respectively. Pressure analysis show the agitation significantly reduces the bed pressure drop, changing the fixed bed below umf and bubbling bed above umf to an agitated bed with a periodic voidage. The DL was proportional to the gas velocity, with little influences of the stirring speed. The radial tracer profiles show the bed is divided by the inner diameter of the helical ribbon into the peripheral ascending region and the central descending region, without gas exchange between them. Furthermore. the tracer profiles in the descending region are classified into two types. For type I, the DR, calculated by the plug flow model with radial dispersion, is proportional to the gas velocity, with little effects of stirring speed. Type II shows uniform profiles due to the deflection of the gas flow toward the low pressure area at the inner diameter of helical ribbon. The causes of the two types are explained by the relative size of particle circulation and gas flux. These two flow regimes are quantitatively clarified with an empirical correlation of Re and Fr as flow regime transition boundary, namely dispersed plug flow and perfect mixing flow. With lower Re and higher Fr, it changes from dispersed plug flow to perfect mixing flow.
Tandem Aromatization of Pentane with Temperature Shifting Three-Stage Fluidized Bed Reactor

Hongmei Wang,Xiang Yu,Chaojie Cui,Jian Wang,Weizhong Qian,Fei Wei

DOI: https://doi.org/10.1016/j.fuel.2022.126850

IF: 7.4

2022-01-01

Fuel

Abstract:Conversion of pentane into aromatics was carried out in a temperature shifting, three-stage fluidized bed reactor, where the temperature was set to be 500 degrees C, 560 degrees C, and 350 degrees C, from the bottom to the top, respectively. The catalysts of Ga/P/ZSM-5 were packed into the first stage (near the bottom of the reactor) and second stage (middle), while catalysts of HZSM-5 were packed into the third (top) stage. Pentane was nearly completely transformed at the first stage, while the aromatics yield was sustainably increased from the first to the second, and finally to the third stage. Detailed product distribution analysis suggested that the aromatization of pentane mainly occurred in the first stage, intermediate products such as C3-C4 paraffins could be effectively transformed via the aromatization reaction in the second stage. Olefins were further transformed into aromatics by the alkylation reaction in the third stage. Within 10 cycles of reaction-catalyst regeneration, stable aromatization with high efficiency was realized for 105 h.
Temperature-dependent Secondary Conversion of Primary Products from Methanol Aromatization in a Two-Stage Fluidized Bed

Zhaohui Chen,Wenlong Song,Yilin Hou,Huiqiu Wang,Chenxi Zhang,Jian Wang,Yifeng Yang,Weizhong Qian

DOI: https://doi.org/10.1016/j.fuel.2020.117204

IF: 7.4

2020-01-01

Fuel

Abstract:Methanol to aromatics (MTA) following dual cycles concept unavoidably produced considerable amounts of olefinic intermediates and paraffinic by-products. Their formation and further conversion were vital to improving aromatics production. In this study, a two-stage fluid bed packed with fluid Zn/ZSM-5 catalyst in each stage was used to investigate the MTA reaction at 470 degrees C in the first stage and the secondary conversion of MTA primary products at temperatures from 270 degrees C to 550 degrees C in the second stage with time on stream. During the MTA reaction, the decrease of catalyst acidity was beneficial to controlling hydrogen transfer, thus blocking propane formation. During the secondary conversion of MTA products, at temperatures below 390 degrees C, the alkylation and hydrogen transfer reactions dominated and thus olefins were converted into more alkylbenzene as well as the undesired propane and butane. As the temperature increased from 430 degrees C to 550 degrees C, the aromatization of light hydrocarbon and the dealkylation of alkylbenzene were facilitated, producing more benzene and toluene but increasing methane and ethane yields. Meanwhile, the dehydrogenation and cracking of propane and butane were favored by high temperature and strong acidity so that the yields of ethene and propene increased. It was clarified that the characteristics of secondary conversion of MTA products varied and depended on reaction temperature and catalyst acidity. Based on these findings, the concept of regional functionalization of fluidized bed reactor was proposed for intensification of MTA process based on the reconfiguration of the temperature and acidity of catalyst stream during the fluidized bed reaction-regeneration cycle.
Conversion of methanol to aromatics in fluidized bed reactor

Tong Wang,Xiaoping Tang,Xiaofan Huang,Weizhong Qian,Yu Cui,Xinyu Hui,Wei Yang,Fei Wei

DOI: https://doi.org/10.1016/j.cattod.2014.02.007

IF: 5.3

2014-01-01

Catalysis Today

Abstract:•Methanol to aromatics conducted in fluidized bed.•Intermediate product of C5+ alkane and alkene was capably converted into aromatics.•Inhibition of gas backmixing in two stage fluidized bed produces more aromatics.
Study of Propane Dehydrogenation to Propylene in an Integrated Fluidized Bed Reactor Using Pt-Sn/Al-SAPO-34 Novel Catalyst

Zeeshan Nawaz,Yue Chu,Wei Yang,Xiaoping Tang,Yao Wang,Fei Wei

DOI: https://doi.org/10.1021/ie902043w

2010-01-01

Industrial & Engineering Chemistry Research

Abstract:Direct propane dehydrogenation is the most economical route to propylene, but very complex due to endothermic reaction requirements, equilibrium limitations, stereochemistry, and engineering constraints. The state of the art idea of bimodal particle (gas-solid-solid) fluidization was applied, in order to overcome alkane dehydrogenation reaction barriers in a fluidized bed technology. in this study, the propane dehydrogenation reaction was studied in an integrated fluidized bed reactor, using Pt-Sn/Al-SAPO-34 novel catalyst at 590 degrees C. The results of fixed bed microreactor and integrated bimodal particle fluidized bed reactors were compared and parametrically characterized. The results showed that the propylene selectivity is over 95%, with conversion between 31 and 24%. This significant enhancement is by using novel bimodal particle fluidization system, owing to uniform heat transfer throughout the reactor and transfer coke from principal catalyst to secondary catalyst, which increases principal catalyst's stability. Experimental investigation reveals that the novel Pt-Sn/Al-SAPO-34 catalyst and proposed intensified design of fluidized bed reactor is a promising opportunity for direct propane dehydrogenation to propylene, with both economic and operational benefit.
A Multi-Stage Fluidized Bed Strategy for the Enhanced Conversion of Methanol into Aromatics

Zhaohui Chen,Yilin Hou,Yifeng Yang,Dali Cai,Wenlong Song,Ning Wang,Weizhong Qian

DOI: https://doi.org/10.1016/j.ces.2019.04.013

IF: 4.7

2019-01-01

Chemical Engineering Science

Abstract:A three-stage fluidized bed strategy was proposed to enhance the conversion of methanol into aromatics (MTA) with Zn/ZSM-5 catalyst, where the 1st stage (near the bottom) served the aromatization of methanol, the 2nd stage (in the middle) served the aromatization of C-3-C-5 paraffins and the 3rd stage (near the exit) served mainly the aromatization of C-2-C-4 olefins in sequence. The yield of aromatics in the 2nd stage increased by 7.0-9.0% compared with the 1st stage. And the final yield of aromatics at the exit of 3rd stage was kept at 62-66% for a long time, 8.0-15.0% higher than that of the exit of 1st stage. The effect of coke deposition in different stages on the evolution of aromatics, olefins and alkanes was investigated to clarify the consecutive reaction chain during MTA. As fully meeting the requirements of the different conversion characteristics of methanol and their intermediates, very high-yield production of aromatics by the single-pass conversion of methanol was achieved with this strategy. (C) 2019 Elsevier Ltd. All rights reserved.
Influence of temperature, residence time, and solvent/feedstock mass ratio on overall product distribution and oil products quality in ethanol liquefaction of 230 polypropylene impact copolymer

Yuqing Li,Zhigang Zhao,Tan Li,Kaige Wang

DOI: https://doi.org/10.1016/j.fuel.2022.123575

IF: 7.4

2022-01-01

Fuel

Abstract:This work examined liquefaction of polypropylene into liquid products in the presence of ethanol with particular attention to the effect of temperature (325-400 & nbsp;C), residence time (1-6 h) and solvent/feedstock mass ratio (1/ 1-4/1) on the overall product distribution, and composition of the oil products. The oil products obtained under the optimal reaction condition contained mainly alkanes, alkenes, alcohols and aromatics, which accounted for 42.41%, 22.81%, 3.51%, 1.05%, respectively. Increasing temperature and retention time enhanced aromatization reaction leading to increased yields of aromatic hydrocarbons. The higher heating value of the oil product was 45.72 MJ/Kg, which is comparable to the higher heating value (HHV) of gasoline. Volatility analysis shows that 50-85 wt% of the oil composition had similar boiling point range as gasoline (35-185 C). These characterization results suggest that the oil could be used as a raw material for gasoline blendstock or chemicals. The interaction of three reaction parameters on the oil formation was further evaluated by the response surface method. Through the Box-Behnken design, the R-2, F-value and p-value of analysis of variance were 0.9917, 93.20, and < 0.0001, respectively, showed that the model fitted well with actual experimental value. It is suggested that the reaction temperature affect the oil yield more significantly, compared to other two parameters. The response surface analysis showed that under the temperature of 376.7 C, residence time 3.8 h and solvent/feedstock mass ratio of 1/1, oil yield of 98.32 wt% can be achieved without adding catalyst or hydrogen. This predication was also verified by experiment.
PRODUCT DISTRIBUTION AND REACTION KINETICS IN THE AROMATIZATION OF YANHUA FCC GASOLINE

Yongmei Zhang,Hongjun You

DOI: https://doi.org/10.17628/ecb.2012.1.108-113

2012-01-01

European Chemical Bulletin

Abstract:y using Yanhua FCC gasoline and a selected fraction of Yanhua FCC gasoline as feedstocks, the effects of reaction temperature, Weight Hour Space Velocity (WHSV), and feedstock performance on yields of LPG, aromatics, and propylene production were investigated in a confined fluidized bed reactor. The experimental result show that yields of aromatics, propylene, and aromatics + propylene for both Yanhua FCC gasoline and fraction of Yanhua FCC gasoline increase with the increase of reaction temperature at the same WHSV. Yields of aromatics, propylene, and aromatics + propylene decrease with the increase of WHSV at the same reaction temperature. Eight-lump kinetics and ten-lump kinetics are pointed out. The experimental results show that both kinetic models can predict the distribution of gasoline conversion and the composition of hydrocarbons of gasoline products under the different reaction conditions.
Efficient conversion of propane in a microchannel reactor at ambient conditions

Chunsong Li,Haochen Zhang,Wenxuan Liu,Lin Sheng,Mu-Jeng Cheng,Bingjun Xu,Guangsheng Luo,Qi Lu

DOI: https://doi.org/10.1038/s41467-024-45179-1

IF: 16.6

2024-01-29

Nature Communications

Abstract:Abstract The oxidative dehydrogenation of propane, primarily sourced from shale gas, holds promise in meeting the surging global demand for propylene. However, this process necessitates high operating temperatures, which amplifies safety concerns in its application due to the use of mixed propane and oxygen. Moreover, these elevated temperatures may heighten the risk of overoxidation, leading to carbon dioxide formation. Here we introduce a microchannel reaction system designed for the oxidative dehydrogenation of propane within an aqueous environment, enabling highly selective and active propylene production at room temperature and ambient pressure with mitigated safety risks. A propylene selectivity of over 92% and production rate of 19.57 mmol m Cu −2 h −1 are simultaneously achieved. This exceptional performance stems from the in situ creation of a highly active, oxygen-containing Cu catalytic surface for propane activation, and the enhanced propane transfer via an enlarged gas-liquid interfacial area and a reduced diffusion path by establishing a gas-liquid Taylor flow using a custom-made T-junction microdevice. This microchannel reaction system offers an appealing approach to accelerate gas-liquid-solid reactions limited by the solubility of gaseous reactant.

multidisciplinary sciences
Production of Acrylic Acid Via Catalytic Partial Oxidation of Propylene in a Two-stage Fluidized Bed

FENG Qi-yao,LUO Guo-hua,WEI Fei

DOI: https://doi.org/10.3321/j.issn:1009-606x.2008.01.015

2008-01-01

Abstract:The experimental results on production of acrylic acid from catalytic partial oxidation of propylene using a single-stage fluidized bed(SSFB)reactor and a two-stage fluidized bed(TSFB)reactor were presented.Experimental investigation for the first-step reaction was conducted on variation of propylene conversion rate and liquid product yield with operating parameters,such as temperature,propylene space velocity,and ratio of oxygen to propylene.The results indicate that the propylene conversion rate and liquid yield in the first-step reaction can be greatly improved up to 94.2%and 74.4%respectively in a two-stage fluidized bed reactor due to effectively suppressing gas backmixing and growth of bubbles in the catalyst bed.Meantime,this work also presented the optimal conditions of space velocity of propylene 20～21 L/(h.kg),operating temperature 360～365℃and molar ratio range of oxygen to propylene 1.6～1.8 in the first-step process.Moreover,the propylene conversion rate and liquid yields in the first-step and two-step process in the acrylic acid production were also examined under the optimal operating conditions.
Methane Aromatization in a Fluidized Bed Reactor: Parametric Study

Javier Lasobras,Jaime Soler,Javier Herguido,Miguel Menéndez,Alonso Jimenez,Mariana da Silva,María J. Franco,Izaskun Barrio,Jesús Làzaro

DOI: https://doi.org/10.3389/fenrg.2019.00008

IF: 3.4

2019-02-14

Frontiers in Energy Research

Abstract:Methane aromatization is a promising technology for the transformation of natural gas into liquid products, but suffers from the problem of catalyst deactivation by coke. A two-zone fluidized bed reactor has been proposed as a tool to counteract the catalyst deactivation, by providing continuous catalyst regeneration in the same vessel where the main reaction is carried out. This work shows the effect of the main operating conditions (carburization temperature, reaction temperature, carburization time, nature of regenerating agent and feed flow and height of the hydrocarbon entry point). Optimal reduction time and temperature were 1 h and 350°C. Best conversion and selectivity were achieved at 700°C without catalyst deactivation in the TZFBR.

energy & fuels
Conversion of Methanol with C5–C6 Hydrocarbons into Aromatics in a Two-Stage Fluidized Bed Reactor

Chang Su,Weizhong Qian,Qing Xie,Yu Cui,Xiaoping Tang,Xiang Yu,Tong Wang,Xiaofan Huang,Fei Wei

DOI: https://doi.org/10.1016/j.cattod.2015.09.022

IF: 5.3

2016-01-01

Catalysis Today

Abstract:The conversion of methanol mixed with C-5-C-6 hydrocarbons (including pentane, hexane, and cyclohexane) was studied in a two-stage fluidized bed reactor packed with 880 g Zn/ZSM-5 catalyst at 475 degrees C and 0.4 MPa. The effect of the mixed feed on the methanol conversion, self-decomposition of methanol, coke deposition on the catalyst, aromatic yield, and the aromatic distribution was carefully studied. Methanol conversion was nearly complete and the self -decomposition of methanol can be suppressed significantly. There exhibited a positive heat coupling effect in the feeding of methanol with pentane or with cyclohexane to increase the aromatic yield or to suppress the undesirable side reactions. However, the mixed feed is unfavorable to the transformation of hexane into aromatics. Better aromatic yield in the lower temperature for the mixed feed, as compared to that for the conversion of pure C-5-C-6 hydrocarbons in higher temperature, validated the heat coupling effect. The result confirmed that it is feasible to use the exothermic methanol conversion to enhance the endothermic transformation of some C-5-C-6 hydrocarbons into aromatic, resulting in a great engineering simplification of heat supply or heat removal in high temperature operation. (C) 2015 Elsevier B.V. All rights reserved.
Modeling of Propane Dehydrogenation Combined with Chemical Looping Combustion of Hydrogen in a Fixed Bed Reactor

Junru Liu,Rui Hu,Xinlei Liu,Qunfeng Zhang,Guanghua Ye,Zhijun Sui,Xinggui Zhou

DOI: https://doi.org/10.1016/j.cjche.2021.07.032

IF: 3.8

2022-01-01

Chinese Journal of Chemical Engineering

Abstract:A redox process combining propane dehydrogenation(PDH) with selective hydrogen combustion(SHC) is proposed, modeled, simulated, and optimized. In this process, PDH and SHC catalysts are physically mixed in a fixed-bed reactor, so that the two reactions proceed simultaneously. The redox process can be up to 177.0% higher in propylene yield than the conventional process where only PDH catalysts are packed in the reactor. The reason is twofold: firstly, SHC reaction consumes hydrogen and then shifts PDH reaction equilibrium towards propylene; secondly, SHC reaction provides much heat to drive the highly endothermic PDH reaction. Considering propylene yield, operating time, and other factors, the preferable operating conditions for the redox process are a feed temperature of 973 K, a feed pressure of 0.1 MPa, and a mole ratio of H 2 to C 3 H 8 of 0.15, and the optimal mass fraction of PDH catalyst is0.5. This work should provide some useful guidance for the development of redox processes for propane dehydrogenation.
Construction of Fluorinated Propane‐Trap in Metal‐Organic Frameworks for Record Polymer‐grade Propylene Production under High Humidity Conditions

Yong Wang,Tong Li,Libo Li,Rui‐Biao Lin,Xiaoxia Jia,Zeyu Chang,Hui‐Min Wen,Xiao‐Ming Chen,Jinping Li

DOI: https://doi.org/10.1002/adma.202207955

IF: 29.4

2023-01-21

Advanced Materials

Abstract:Propane/propene (C3H8/C3H6) separation is essential in the petrochemical industry but challenging because of their similar physical and chemical properties. Adsorptive separation with C3H8‐selective porous materials can energy‐efficient produce high‐purity C3H6, which is highly promising for replacing conventional cryogenic distillation but suffers from unsatisfactory performance. Herein, through the precise introduction of fluorinated functional groups into the confined pore space, a new fluorinated MOF (FDMOF‐2) featuring the unique strong C3H8‐trap was successfully constructed. FDMOF‐2 exhibit an unprecedented C3H8 capture capacity of 140 cm3 cm−3 and excellent C3H8/C3H6 (1:1, v/v) selectivity up to 2.18 (298 K and 1 bar), thus setting new benchmarks for all reported porous materials. Single‐crystal X‐ray diffraction studies reveal that the tailor‐made pore confinement in FDMOF‐2 provided stronger and multiple attractive interactions with C3H8, enabling excellent binding affinities. Breakthrough experiments demonstrate that C3H8 can be directly extracted from various C3H8/C3H6 mixtures through FDMOF‐2, affording an outstanding C3H6 production (501 mmol L−1) with over 99.99% purity. Benefiting from the robust framework and hydrophobic ligands, the separation performance of FDMOF‐2 can be well maintained even under 70% relative humidity conditions. The exceptional propylene separation productivity and ultrahigh structural stability make this MOF material a very promising candidate for this challenging separation process. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Process Design and Analysis of Aromatics Production from Coal Via Methanol with a High Yield

Jianrong Jiang,Dan Zhang,Xiao Feng,Minbo Yang,Yufei Wang

DOI: https://doi.org/10.1021/acs.iecr.1c00421

2021-01-01

Industrial & Engineering Chemistry Research

Abstract:Producing aromatics from coal via methanol is a novel technology, which could mitigate the energy shortage in a petroleum-poor area. However, the selectivity of methanol to aromatics is merely 40-70 wt % due to the byproducts of light hydrocarbons. In this paper, three novel designs are proposed to improve the aromatics yield by directly or indirectly converting light hydrocarbons into aromatics. In addition, cofeeding of coal and natural gas is applied in two of the three designs. On the basis of detailed process modeling and simulation, the process designs are assessed by mass balance, technoeconomic, and life cycle analyses. The results show that the aromatics yield is significantly improved by integrating light hydrocarbon conversion units. The CO2 emissions and water consumption are notably decreased in the two cofeeding designs. In addition, the net present value of the design integrated with steam reforming of C2- hydrocarbons and aromatization of C3+ hydrocarbons is the highest, about 1.9 times as much as that of the nonintegrated design. The cofeeding design integrated with steam reforming of C2- hydrocarbons and aromatization of C3+ hydrocarbons leads to the lowest global warming potential and abiotic depletion potential, only 46.1 and 71.1% of the nonintegrated design, respectively. It implies that a more complex design shows better environmental performances.
An Orthogonal Method for Aromatization Reactions of Shenghua Fcc Gasoline

H. You

DOI: https://doi.org/10.1080/10916460600705832

IF: 1.695

2008-01-01

Petroleum Science and Technology

Abstract:Using a confined fluidized bed reactor and aromatization catalysts (LBO-A and LBO-16), the aromatization performance of Shenghua fluid catalytic cracking (FCC) gasoline has been studied in an orthogonal method. The experimental results reveal that the optimum reaction condition for the light oil yield was reaction temperature 420 degrees C, WHSV 40 h(-1), mass ratio catalyst to oil 4 and 75% LBO-A and 25% LBO-16; the optimum reaction condition for aromatics amount in the light oil was reaction temperature 420 degrees C, WHSV 30 h(-1), mass ratio catalyst to oil 5 and 65% LBO-A and 35% LBO-16, the olefin content is remarkably reduced from about 54.7% to 12.8% and 8.7% (by mass), respectively, at the same time the reaction mechanism of aromatization reaction is put forward based on the experimental result.
Aromatics Production Via Catalytic Pyrolysis of Pyrolytic Lignins from Bio-Oil

Yan Zhao,Li Deng,Bin Liao,Yao Fu,Qing-Xiang Guo

DOI: https://doi.org/10.1021/ef100896q

IF: 4.6541

2010-01-01

Energy & Fuels

Abstract:Herein we reported a promising method for the production of aromatics from pyrolytic lignin (PL). Compared to the lignins derived from pulping process, the PLs obtained from bio-oil give more aromatics (40% in carbon yield) and do not generate effluvial gas containing sulfur. More importantly, phenols are the main products with selectivity over 90% at 600 degrees C without catalyst. In the presence of ZSM-5, the coke deposition was not obvious and the selectivity for aromatic hydrocarbons is more than 87%, indicating robustness of ZSM-5 for deoxygenating and high tolerance to PLs. Therefore we have demonstrated the catalytic pyrolysis of PLs is an alternative way to produce fuel additives and useful chemicals.
Highly selective and stable Zn–Fe/ZSM-5 catalyst for aromatization of propane

Gbenga Godwin Oseke,Abdulazeez Yusuf Atta,Bello Mukhtar,Baba Yakubu Jibril,Benjamin Olorunfemi Aderemi

DOI: https://doi.org/10.1007/s13203-020-00245-9

2020-05-18

Applied Petrochemical Research

Abstract:Abstract Light alkane aromatization for aromatic compound production, used in petrochemical industries is an attractive area of research. The effect of second metal co-impregnation was investigated in stabilizing zinc on ZSM-5 in aromatization of propane. HZSM-5 was modified with zinc and iron metal by co wet-impregnation and characterized using XRF, XRD, BET, N 2 -adsorption, FTIR, FTIR-Pyridine, SEM, TEM, H 2 -TPR and XPS. The effect of different loadings of Iron on Zn/ZSM-5 was investigated on acidity, aromatic yield, product distribution and aromatization performance. Performance test was conducted in a fixed bed reactor at 540 °C, one atmosphere. GHSV of 1200 mL/g-h. Co-impregnation of Zn with Fe improved the catalytic activity and aromatic yield for 10 h time on stream as compared to parent HZSM-5 and Zn/ZSM-5 of very low aromatic yield and propane conversion. Impregnation of Zn as the dehydrogenating metal on HZSM-5 steadily increased aromatic yield from 5% on HZSM-5 to 25% and was steadily dropped to 20% after 10 h TOS. The co-impregnation of iron of 1–3 wt% loading as the second metal for zinc stability with 2 wt% Zn on ZSM-5 improved propane conversion and aromatic yield to 55% for the 10 h TOS. This further enhanced aromatic product distribution and minimized light gases.

Enhanced Production of Aromatics from Propane with a Temperature-Shifting Two-Stage Fluidized Bed Reactor.

High-yield Production of Aromatics from Methanol Using a Temperature-Shifting Multi-Stage Fluidized Bed Reactor Technology

Thermodynamic Analysis of Propane Aromatization

Mixing Effects on the Gas Flow and Mass Transfer in a Vertical Single Helical Ribbon Agitated Reactor for Propylene Polymerization

Tandem Aromatization of Pentane with Temperature Shifting Three-Stage Fluidized Bed Reactor

Temperature-dependent Secondary Conversion of Primary Products from Methanol Aromatization in a Two-Stage Fluidized Bed

Conversion of methanol to aromatics in fluidized bed reactor

Study of Propane Dehydrogenation to Propylene in an Integrated Fluidized Bed Reactor Using Pt-Sn/Al-SAPO-34 Novel Catalyst

A Multi-Stage Fluidized Bed Strategy for the Enhanced Conversion of Methanol into Aromatics

Influence of temperature, residence time, and solvent/feedstock mass ratio on overall product distribution and oil products quality in ethanol liquefaction of 230 polypropylene impact copolymer

PRODUCT DISTRIBUTION AND REACTION KINETICS IN THE AROMATIZATION OF YANHUA FCC GASOLINE

Efficient conversion of propane in a microchannel reactor at ambient conditions

Production of Acrylic Acid Via Catalytic Partial Oxidation of Propylene in a Two-stage Fluidized Bed

Methane Aromatization in a Fluidized Bed Reactor: Parametric Study

Conversion of Methanol with C5–C6 Hydrocarbons into Aromatics in a Two-Stage Fluidized Bed Reactor

Modeling of Propane Dehydrogenation Combined with Chemical Looping Combustion of Hydrogen in a Fixed Bed Reactor

Construction of Fluorinated Propane‐Trap in Metal‐Organic Frameworks for Record Polymer‐grade Propylene Production under High Humidity Conditions

Process Design and Analysis of Aromatics Production from Coal Via Methanol with a High Yield

An Orthogonal Method for Aromatization Reactions of Shenghua Fcc Gasoline

Aromatics Production Via Catalytic Pyrolysis of Pyrolytic Lignins from Bio-Oil

Highly selective and stable Zn–Fe/ZSM-5 catalyst for aromatization of propane