Abstract:A site-specific xenon plasma focused ion beam preparation technique for microcantilever samples (1-20 µm width and 1:10 aspect ratio) is presented. The novelty of the methodology is the use of a chunk lift-out onto a clean silicon wafer to facilitate easy access of a low-cost probe type indenter which provides bending force measurement. The lift-out method allows sufficient room for the indenter and a line of sight for the electron beam to enable displacement measurement. An electroplated nanotwinned copper (NTC) was cut to a 3 × 3 × 25 µm microbeam and in situ mechanically tested using the developed technique. It demonstrated measured values of Youngs modulus of 78.7 ± 11 GPa and flow stress of 0.80 ± 0.05 GPa, which is within the ranges reported in the literature. LAY DESCRIPTION: In this paper a site specific method is present for making particularly small mechanical tests samples, of the order of 100th the size of a human hair. These small samples can then be used to determine the mechanical properties of the bulk material. Copper with a nano twinned grain structure is used as a test medium. Ion milling was used to cut the sample to shape and a micro probe was used for mechanical testing. Ion milling can cut away very small volumes of material as it accelerates ions at the surface of the sample, atomically machining the sample. Micro probes are a cost-effective small-scale load measurement devices, however, they require a large area for accessing the sample. The indenter requirements are a problem when making you samples with ion milling as ion millers are best at making small cuts. Our aim was to design a cutting strategy which reduces the amount of cutting required while allowing samples to be fabricated anywhere on the sample. We used a chunk lift out technique to remove a piece of material which is then welded to a wafer of silicon this gives sufficient space around the sample for ion milling and testing. The additional space allowed easy access for the probe. A 3 × 3 × 10 µm micro cantilever beam was cut out from copper, this beam was then bent. The force from bending and distance bent was measured and converted into Youngs modulus which is a measure of flexibility. The modulus value measured was comparable to the values reported in other papers.

A Method for Measuring Resistance of Metal Interconnection Inside Chip

MMIC on-Wafer Test Method Based on Hybrid Balanced and Unbalanced RF Pad Structures

Methodology for Measurement of Submicron Metallic Wire's Local Electrical Conductivity by Applying Four-points AFM Probe Technique

Method for Accurate Measurement of Micro-Nano Thin Film Device Resistivity

An improved method for test chip design

An Efficient Metrology to Sense Micro-Metal Contamination in Fine-Pitch Package

A Two-Port Measurement With Mechanically Robust Handhold Probes for Ultra Low PDN Impedance

Modeling and Measurement of A Novel Shielding Design in Silicon Interposer

Virtual instrumentation based automatic thin film resistivity measurement system

An Enhanced One-Port Waveguide Method for Sheet Resistance Extraction

Conductivity Measurement Technique for Interface and Surface Using Dielectric Rod Resonator Based on Calibration

Characterization of Micro-Contact Resistance Between A Gold Nanocrystalline Line and A Tungsten Electrode Probe in Interconnect Fatigue Testing

High-Throughput Measurement of the Contact Resistance of Metal Electrode Materials and Uncertainty Estimation

In-situ Measurement Methods of the Metal Layer Thickness on Wafer with Nanometer Precision

Wafer-Area-Saving Test Structures and Measurement Method for the Characterization of Interconnect Resistance and Capacitance in Nanometer Technologies

Focused ion beam preparation of microbeams for in situ mechanical analysis of electroplated nanotwinned copper with probe type indenters

A Contactless Testing Methodology for Pre-Bond Interposer

Modeling And Analysis Of Metal Interconnect Resistance Of Power Ic'S

In Situ Monitoring of Flip Chip Package Process Using Thermal Resistance Network Method and Active Thermography

Two-Dimensional Dense-Arrayed Probe-Cards with A Hoe-Shaped Probing-Tip Micromachining Technique

Metal hard-mask based AIO etch challenges and solutions