Abstract:High-work function (WF) transparent conductive thin films improve the performance of solar cells and organic light-emitting diodes by facilitating interfacial charge carrier transport. Al-doped ZnO (AZO) becomes a very promising transparent conductive material because of nontoxicity, abundant material resources, and low cost. To increase the WF of AZO without enhancing the series resistance of the device, a high-WF and low-resistance surface modifier of polycrystalline zinc molybdenum oxide (ZMO) was developed by utilizing thermal evaporation of MoO3 on the surface of AZO and a subsequent two-step annealing treatment. The first step of air annealing causes the formation of monoclinic ZnMoO4 nanocrystals in the ZMO modifier. This improves the WF of AZO from 3.83 to 4.86 eV by increasing the group electronegativity and cation oxidation state. Furthermore, the second step of N2 annealing decreases the resistivity of the polycrystalline ZMO by increasing the donor states of oxygen vacancies. The surface modification effect is verified by applying the ZMO-modified AZO to the front electrode of hydrogenated amorphous silicon thin-film solar cells. The low-resistance polycrystalline ZMO modifier not only increases light harvesting in the solar cells by improving interfacial refractive index matching but also improves the open-circuit voltage by modifying the interfacial band alignment. In particular, the modifier increases the fill factor by ca. 13% by reducing the series resistance of the device. These enable a gain of ca. 23% in photoelectric conversion efficiency compared to the unmodified AZO. The results suggest the feasibility to tune the WF and conductivity of a material independently.

Surface Modification of Al-Doped ZnO Transparent Conducive Thin Films with Polycrystalline Zinc Molybdenum Oxide.

Highly Surface-Textured ZnO:Al Films Fabricated by Controlling the Nucleation and Growth Separately for Solar Cell Applications

Simulation, Fabrication, and Application of Transparent Conductive Mo-Doped Zno Film in A Solar Cell

Highly Surface-Textured and Conducting Zno:Al Films Fabricated from Oxygen-Deficient Target for Cu(In, Ga)Se-2 Solar Cell Application

Fabrication of High-Performance F and Al Co-Doped ZnO Transparent Conductive Films for Use in Perovskite Solar Cells

Improvement of electrical and optical properties of molybdenum doped zinc oxide films by introducing hydrogen

Tailoring the Morphology, Optical and Electrical Properties of DC-sputtered ZnO:Al Films by Post Thermal and Plasma Treatments

Preparation of Aluminum Doped Zinc Oxide Films with Low Resistivity and Outstanding Transparency by a Sol–gel Method for Potential Applications in Perovskite Solar Cell

Aluminum and Molybdenum Co-Doped Zinc Oxide Films as Dual-Functional Carrier-Selective Contact for Silicon Solar Cells

Development of Textured ZnO∶Al Transparent Conductive Oxide Thin Films

The enhanced conductivity and stability of AZO thin films with a TiO 2 buffer layer

Modulation of the TCO/MoO x Front Contact Enables >21% High-Efficiency Dopant-Free Silicon Solar Cells

Wet-chemical surface texturing of AZO substrate for improved perovskite solar cells

Synthesis of ZnO:Al Transparent Conductive Thin Films Using Sol-gel Method

The properties of surface textured ZnO:Al films grown in hydrogen atmosphere

Tailoring of Optical and Electrical Properties of Transparent and Conductive Al-doped ZnO Films by Adjustment of Al Concentration

Modified Textured Surface Mocvd-Zno:B Transparent Conductive Layers for Thin-Film Solar Cells

Structural ,Electrical ,and Optical Properties of Transparent Conductive Al-Doped ZnO Films Prepared by RF Magnetron Sputtering

Self-Flattened ZnO:Al Transparent Conductive Thin Films Derived by Sol–Gel Process

Band Alignment Tuning at Mo/CZTS Back Contact Interface Through Surface Oxidation States Control of Mo Substrate

High Haze and Low Resistive MgO/AZO Bi-layer Transparent Conducting Oxide for Thin Film Solar Cells