Abstract:Flow softening behavior, microstructure evolution and hot working parameters of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy were systematically studied by isothermal hot compression. Based on the analysis of processing maps and the corresponding microstructure, power dissipation efficiency peak occurred at two domains, which were associated with dynamic recrystallization (DRX) and super-plasticity. Pile-up of high density dislocation and a large number of twins were the primary deformation mechanisms at low temperature and high strain rate. As the temperature increases, fine DRX grains promote the movement and rotation of grain boundary, the softening of β phase and the transformation of β→α/α2+γ above 1200 °C improve the deformation capacity of the alloy significantly. Crack-free TiAl sheets were successfully obtained by direct hot rolling process at 1080 °C and 1220 °C. The corresponding microstructure and mechanical properties were analyzed. The sheets rolled at 1080 °C was characterized by near γ (NG)+β0 microstructure with a streamline along the rolling direction, while duplex (DP)+β0 microstructure appeared to be the main microstructure at rolling temperature of 1220 °C. The as-rolled sheet exhibits excellent mechanical properties at 800 °C. The sheet rolled at 1080 °C exhibits 320 MPa yield strength and 468 MPa ultimate tensile strength with 142% elongation. The yield strength, ultimate tensile strength, and elongation of the as-rolled sheet are 446 MPa, 586 MPa, and 3.0%, respectively, when rolled at 1220 °C. The excellent ductility of the sample rolled at 1080 °C is attributed to formation of fine DRX grains due to consumption of twins and substructure under tensile stress, which promote grain boundary slip. Lamellar colonies with fine interlamellar spacing and α2 laths formed at 1220 °C can effectively prevent dislocation motion, resulting in a significant increase in the strength of the alloy.

Microstructure and High-Temperature Mechanical Properties of Second-Phase Enhanced Mo-La2O3-ZrC Alloys Post-Treated by Cross Rolling

Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys

Enhanced Mechanical Properties and Thermal Stability of Hot-Rolled Mo-0.5%ZrC Alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Effect of Zr on microstructure evolution of Ti-Mo composite microalloyed steel during rolling

Rolling parameters, microstructure control, and mechanical properties of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy: The impact of rolling temperatures

The Mechanical Properties of the Mo-0.5Ti and Mo-0.1Zr Alloys at Room Temperature and High Temperature Annealing

Effect of Rolling Temperature on Microstructure and Properties of Al-Mg-Li Alloy

Microstructure evolution and recrystallization of Ti-44.5Al-3.8Nb-1Mo-0.2B alloy with different initial microstructure during hot pack rolling

Effect of Microstructure Evolution on Mechanical Properties of a TiZrAlB Alloy Rolled by Different Processes

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy

Change in Microstructures and Mechanical Properties of Biomedical Ti-Nb-Ta-Zr System Alloy through Cross-Rolling

Effect of cold rolling on the microstructure and mechanical properties of MG-8GD-3Y-0.5ZR alloy

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Effects of Rolling Deformation on Precipitation Behavior and Mechanical Properties of Al–Zn–Mg–Cu Alloy

Crack Initiation Mechanism in Lanthanum-Doped Titanium-Zirconium-molybdenum Alloy During Sintering and Rolling

Secondary phases strengthening-toughening effects in the Mo–TiC–La2O3 alloys

Effect of Rolling Strain on Microstructure and Tensile Properties of Dual-Phase Mg–8Li–3Al–2Zn–0.5Y Alloy

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling