Abstract:Thin-film transistors (TFTs) with a small pitch size are necessary to realize high-resolution displays for virtual reality and augmented reality applications. Particularly, electrodes require low-resistance metals to reduce the resistance–capacitance delay caused by the increased pixel density. However, low-resistance Al can easily oxidize in bottom-contact structures of vertical TFTs owing to the oxidative deposition environment. This study quantitatively analyzed the contact properties of an Al-based metal with Mo and Ti capping layers. The Mo/Al/Mo and Ti/Al/Ti were adopted as the source/drain (S/D) electrodes, and their contact properties were compared. The top-gate bottom-contact device with Mo/Al/Mo S/D exhibited better contact properties, with a 0.02 V turn-on voltage (Von), 3.5× 107 ON/OFF ratio, and 5.7 kΩ contact resistance (RSD). By contrast, the device with Ti/Al/Ti S/D exhibited degraded characteristics, with a -0.3 V Von, 0.9 × 107 ON/OFF ratio, and 17 kΩ RSD owing to metal oxidation. The contact properties were further examined through ultraviolet photoelectron spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy. Vertical TFTs were fabricated using Mo/Al/Mo and Ti/Al/Ti electrodes, and their electrical properties were investigated. The vertical TFT with Mo/Al/Mo electrodes exhibited reasonable performance, with a field-effect mobility of 3.3 cm2/Vs and RSD of 15 kΩ. Conversely, the device with Ti/Al/Ti electrodes yielded degraded transfer characteristics, with a mobility of 0.05 cm2/Vs and RSD of 984 kΩ. The analysis indicates that electrode materials significantly influence the electrical performance of vertical TFTs. Therefore, electrode materials must be carefully selected and structured to realize high-end vertical TFT arrays.

An Asymmetric Metal Electrode for TFT-LCDs

Contact Properties of a Low-resistance Aluminum-based Electrode with Metal Capping Layers in Vertical Oxide Thin-film Transistors

Formation Mechanism and Prevention of Cu Undercut Defects in the Photoresist Stripping Process of MoNb/Cu Stacked Electrodes

Optimization of Thin Metal Layer Etch Process for MEMS/Sensor Application*

A Study about the Different Corrosion Behavior Between Cu/Mo Bilayer and Mo/Cu/Mo Three-layer Metal Electrode

High-performance and Reliable Elevated-Metal Metal-Oxide Thin-Film Transistor for High-Resolution Displays

Optimization Of Thin Metal Layer Etch Process For Hems/Sensor Application

Corrosion-controlled surface engineering improves the adhesion of materials for stable free-standing electrodes

Wet-Etch Method for Patterning Metal Electrodes Directly on Amorphous Oxide Semiconductor Films

Tapered Cu Pattern Metallization by Electrodeposition Through Mask

Improved Performance of the Amorphous Indium-Gallium-zinc Oxide Thin Film Transistor with Cu-Mo Source/drain Electrode

Channel-Shortening Effect Suppression of a High-Mobility Self-Aligned Oxide TFT Using Trench Structure

Elevated-Metal Metal-Oxide (EMMO) Thin-Film Transistor: Technology and Characteristics

Optimizing the interfacial potential distribution to mitigate high transient potential induced dissolution on C/Ti coated metal bipolar plates used in PEMFCs

Asymmetric Chemical Functionalization of Top‐Contact Electrodes: Tuning the Charge Injection for High‐Performance MoS 2 Field‐Effect Transistors and Schottky Diodes

Modulation of the Al/Cu2O Schottky Barrier Height for p-Type Oxide TFTs Using a Polyethylenimine Interlayer

Elevated Metal Metal-Oxide Thin-Film Transistor — A New Bottom-Gate Transistor Architecture for Flat-Panel Displays

High-Performance Flexible Transparent Electrode with an Embedded Metal Mesh Fabricated by Cost-Effective Solution Process.

Eliminating light depolarization from metal microstructure in liquid crystal displays

Self-Aligned Elevated-Metal Metal-Oxide Thin-Film Transistors for Displays and Flexible Electronics

Overcoming the Limitations of MXene Electrodes for Solution‐Processed Optoelectronic Devices