Abstract:(SiC+TiB 2 )/AlSi10Mg composite powders with 5 wt% micro-SiC particles and 1.5 wt% nano-TiB 2 particles were prepared by high energy ball milling, and hybrid particle reinforced aluminum matrix composites (AMCs) were fabricated by SLM. This study systematically investigated the effects of SiC and TiB 2 particles on the phase composition, microstructure evolution, grain crystallization, and mechanical properties. The machanisms of potential strengthening and fracture mechanisms were revealed. The tribological behaviors of the hybrid particle reinforced AlSi10Mg composites under different friction conditions were explored as well. The results show that the 1.5 wt% nano-TiB 2 particles provided sufficient nucleation sites for grain growth, completely transforming from coarse columnar to fined equiaxed grains. The average grain size decreases from 7.98 μm to 3.34 μm, and the texture is significantly weakened, which is beneficial to the homogenization of the microstructure, thereby improving the mechanical properties of the SiC/AlSi10Mg composites. The (SiC+TiB 2 )/AlSi10Mg composites showed a high ultimate tensile strength (∼ 489.1 MP), hardness (172.2 HV) and elongation of 8.2 %. The enhancement of mechanical properties was attributed to Orowan strengthening, fine grain strengthening, and load-bearing strengthening. Due to the Si precipitates and fine microstructure, a low wear rate of 0.50 × 10 −5 g/m was obtained, 10.7 % lower than that of SLM formed SiC/AlSi10Mg composites. The friction process is affected by abrasive wear, adhesive wear and delamination wear. It is aspired that the current approach can provide guidance for the design of new alloy systems with excellent performance.

Sialon Tailoring Copper-Based Composite to Achieve High Strength, High Strain Integrated with Excellent Wear Resistance

The Tribological Properties and Wear Mechanism of Copper Coated Graphite Doped Sialon Ceramic Composites at Wide Range Temperature from 25 to 800 °C

In situ synthesis of PcBN composites by Sialon combined with cBN-TiB2-AlN and their properties

High-performance TiN Reinforced Sialon Matrix Composites: A Good Combination of Excellent Toughness and Tribological Properties at a Wide Temperature Range

Effect of hBN addition on the fabrication, mechanical and tribological properties of Sialon materials

High strength and high electrical conductivity Cu composites reinforced by SiO 2 aerogel particles

Enhancing mechanical properties of copper matrix composite by adding SiO2 quantum dots reinforcement

Abrasive wear behavior of Sialon ceramic

Mechanical properties of Cu/SiCp composites fabricated by composite electroforming

Optimisation of Properties of Ti3SiC2 Reinforced Copper Matrix Composites

Microstructure and mechanical behavior of carbon fiber reinforced carbon, silicon carbide, and copper alloy hybrid composite fabricated by Cu-Si alloy melt infiltration

Microstructure, mechanical and tribological properties of Cu-Sn/Cr3C2/Gr composites

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Compressive Strength, Wear, and Structure Characteristics as a Result of Silicon Carbide Addition on a Copper Base

Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Enhancement of Tribological Properties in Siliconized Graphite Via Hierarchically Hybrid SiC/C Composite

Microstructure and Room-Temperature Mechanical Properties of Β Sialon/sic Nanocomposites

A novel sintering method of Al2O3/SiCw ceramic composites with improved wear resistance: Oscillatory pressure‐assisted sinter forging

Effect of Heat Treatment on Tribological Properties of SiCp/Al–Mg–Mn–Cu Aluminum Matrix Composites

Preparation, structure and mechanical properties of Sialon ceramics by transition metal-catalyzed nitriding reaction