Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Microstructure and Room-Temperature Mechanical Properties of Β Sialon/sic Nanocomposites

In situ synthesis of PcBN composites by Sialon combined with cBN-TiB2-AlN and their properties

Si3N4-SiC ceramic nanocomposites

Microstructure And Mechanical Properties Of Sic Ceramic Toughened With Tin Nanoparticles

Microstructure, mechanical properties and thermal conductivity of (Ti0.5Nb0.5)C–SiC composites

Hot strength and microstructure of β-sialon-Al2O3-SiC composites

HOT STRENGTH AND MICROSTRCTURE OF Βsialonal_2o_3sic COMPOSITES

Effects of in situ Mg-Sialon and β-Sialon on the microstructure and properties of MgAl2O4-SiC composites

Microstructure and Fracture Behavior of Β-Si3n4 Based Nanoceramics

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

Microstructures and mechanical properties of in-situ SiC-TiB2 ceramic composites fabricated by reactive melt infiltration

Microstructure and mechanical properties of SiC-Al2O3 nanocomposite prepared by surface modified SiC nanopowders

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

β→α Phase Transformation and Properties of Solid-State-Sintered SiC Ceramics with TaC Addition

Effect of Nano SiC on Microstructure and Mechanical Properties of BN-ZrO2-SiC Multiphase Ceramics

Microstructure and Mechanical Properties of Unidirectional, Laminated Cf/SiC Composites with α-Al2O3 Nanoparticles as Filler

Microstructure and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>/SiC Nanocomposites Prepared by SPS

Mechanical properties of silicon carbide—in situ zirconium carbonitride composites

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

Mechanical Property and Ballistic Performance of Silicon Carbide

Synthesis of cBN-hBN-SiCw Nanocomposite with Superior Hardness, Strength, and Toughness