Abstract:h-BN-ZrO2-SiC multiphase ceramics were prepared rapidly by spark plasma sintering (SPS) with h-BN, ZrO2 and SiC powders as raw materials and 8% (Al2O3+Y2O3) as sintering aids. The effects of nano SiC content on the densification, microstructure and mechanical properties of h-BN-ZrO2-SiC multiphase ceramics were investigated. The results show that the addition of nano SiC particles can effectively promote the sintering and increase density and mechanical properties of the sintered samples at a low sintering temperature. The flexural strength, fracture toughness and elastic modulus all increase with the content increase of nano SiC, especially, the increment of the elastic modulus is obvious. The comparison of all results shows that the sample with the SiC content of 25% has optimal mechanical properties, and the flexural strength, fracture toughness and elastic modulus are 268.4 MPa, 3.24 MPa.m(1/2) and 115 GPa, respectively. It is mainly because the nano SiC particles can better play a gap filling, dispersion strengthening and grain boundary pinning effect than ZrO2, which are beneficial to improve the bonding strength between the phases and reduce the residual stress due to thermal mismatch. As a result, more fracture energy is absorbed during the crack propagation process, and the flexural strength and fracture toughness increase.

Microstructure and Fracture Behavior of Β-Si3n4 Based Nanoceramics

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Indentation deformation and microcracking in β-Si 3N 4-based nanoceramic

Microstructure and Mechanical Properties of TiN/Si3N4 Nanocomposites by Spark Plasma Sintering (SPS)

Influence of Conductive Nano-Tic on Microstructural Evolution of Si3n4-Based Nanocomposites in Spark Plasma Sintering

Processing and Characterization of SiB0.5C1.5N0.5 Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

Effect of Pure Β-Si3n4powder on Microstructure and Mechanical Properties of Porous Si3N4ceramics

Mechanical properties and microstructure of laminated Si3N4+SiCw/BN+Al2O3 ceramics densified by spark plasma sintering

Effect of Si/C Ratio and Their Content on the Microstructure and Properties of Si–B–C–N Ceramics Prepared by Spark Plasma Sintering Techniques

Microstructure and Properties of Porous Si3n4 Ceramics with A Dense Surface

Effect Of Microstructural Modification On Thermal Conductivity And Strength Of Silicon Nitride

Microstructure and mechanical properties of spark plasma sintered SiC ceramics aided by B4C

Microwave Sintering of Si3N4 Ceramics

The Effect of Microstructure on Fracture Toughness for Silicon Nitride Ceramics

Effect of Nano SiC on Microstructure and Mechanical Properties of BN-ZrO2-SiC Multiphase Ceramics

Fabrication and Mechanical Properties of Boron Nitride Nanotube Reinforced Silicon Nitride Ceramics

Study on Microstructure and Mechanical Properties of Porous Si<sub>3</sub>N<sub>4</sub> Ceramics

Microstructure and properties of nano-laminated Y3Si2C2 ceramics fabricated via in situ reaction by spark plasma sintering

The dependence of interlocking and laminated microstructure on toughness and hardness of β-SiC ceramics sintered at low temperature

Microstructures and Mechanical Properties of Pressureless Sintered Ca-3(PO4)(2)/Si3N4 Composite Ceramics

Microstructure Control and Mechanical Properties of Porous Silicon Nitride Ceramics