Abstract:The present study investigated the densification behavior, microstructure and wear properties of Ti-Nb2O5 based composites processed by spark plasma sintering (SPS). The SPS process was performed using sintering temperature of 1000 °C, holding time 10 min, heating rate 100 °C/min and applied pressure 50 MPa, as sintering process parameters. Optical and Scanning electron microscopy, X-Ray diffractometry, Relative density and hardness measurement, coefficient of friction and wear rate evaluation were used to characterize the composites produced. The CpTi and Ti-Nb2O5 composites attained full densification (relative densities ranged from 99.57 to 99.94%), and the total sintering times and densification stages were independent of the Nb2O5 reinforcement. However,the sinterability of the composites improved with increase in Nb2O5 content. The punch displacement curve of the Nb2O5 reinforced CpTi composite grades were higher compared to the CpTi. Also, the hardness values increased progressively with increase in Nb2O5 content. The microstructures that the addition of Nb2O5 resulted in structural transformation from lamellar (α) in the Cp Ti to bimodal (α+β) structures in the Ti-Nb2O5 composites accompanied with decrease in average grain size with increase in Nb2O5 content. The steady-state friction coefficients for all the composite samples ranged from 0.3 to 0.6. However, there was largely progressive increase in friction coefficient with Nb2O5 content. Generally, the wear resistance increased with increase in Nb2O5 content with the wear mechanism of the composites from wear track assessment, established to be mixed mode of adhesive and abrasive wear.

Microstructure and Mechanical Properties of TiN/Si3N4 Nanocomposites by Spark Plasma Sintering (SPS)

Influence of Conductive Nano-Tic on Microstructural Evolution of Si3n4-Based Nanocomposites in Spark Plasma Sintering

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Microstructure and Fracture Behavior of Β-Si3n4 Based Nanoceramics

Fabrication and mechanical evaluation of SiC–TiC nanocomposites by SPS

Microstructure and Mechanical Properties of Ti3sic2/3y-Tzp Composites by Spark Plasma Sintering

Microstructure and Mechanical Properties of Composites Obtained by Spark Plasma Sintering of Ti3SiC2-15 vol.%Cu Mixtures

Densification characteristics, microstructure and wear behaviour of spark plasma sintering processed titanium-niobium pentoxide (Ti-Nb2O5) based composites

Microstructure and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>/SiC Nanocomposites Prepared by SPS

Microstructure, densification and mechanical properties of in situ TiBw/Ti2AlNb composites fabricated by spark plasma sintering

Microstructure And Mechanical Properties Of Sic Ceramic Toughened With Tin Nanoparticles

Preparation and Characterization of Tic-Sic Composites Sintered by Sps

Effect of spark plasma sintering temperature on the multi-scale microstructure evolution and mechanical properties of Ti 2 AlC/TiAl composites with network architecture

Densification, Microstructure and Mechanical Performance of TiC/Fe Composites by Spark Plasma Sintering

Microstructure and mechanical behaviour of transient liquid phase spark plasma sintered B4C–SiC–TiB2 composites from a B4C–TiSi2 system

Microstructure, Mechanical Properties, and Sintering Behavior of Ti3O-Fe2TiO4-TiC Composites

Microstructure and Properties of TiN-reinforced W–Ti Alloys Prepared by Spark Plasma Sintering

Fabrication and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>-Ti<sub>3</sub>SiC<sub>2</sub> Composites by SPS

Spark plasma sintering of TiN ceramics codoped with SiC and CNT

Effects of Ti(C, N) addition on the microstructure and mechanical properties of spark plasma sintered Si3N4/Ti(C, N) ceramic tool material

Effect of NiTi content on the mechanical properties and microstructure of TiB2–TiN-based composite ceramic material prepared using spark plasma sintering