Abstract:Method of soft metal (Cu) strengthening of Ti3SiC2 was conducted to increase the hardness and improve the wear resistance of Ti3SiC2. Ti3SiC2/Cu composites containing 15 vol.% Cu were fabricated by Spark Plasma Sintering (SPS) in a vacuum. The effect of the sintering temperature on the phase composition, microstructure and mechanical properties of the composites was investigated in detail. The as-synthesized composites were thoroughly characterized by scanning electron micrography (SEM), optical micrography (OM) and X-ray diffractometry (XRD), respectively. The results indicated that the constituent of the Ti3SiC2/Cu composites sintered at different temperatures included Ti3SiC2, Cu3Si and TiC. The formation of Cu3Si and TiC originated from the reaction between Ti3SiC2 and Cu, which was induced by the presence of Cu and the de-intercalation of Si atoms Ti3SiC2. OM analysis showed that with the increase in the sintering temperature, the reaction between Ti3SiC2 and Cu was severe, leading to the Ti3SiC2 getting smaller and smaller. SEM measurements illustrated that the uniformity of the microstructure distribution of the composites was restricted by the agglomeration of Cu, controlling the mechanical behaviors of the composites. At 1000 °C, the distribution of Cu in the composites was relatively even; thus, the composites exhibited the highest density, relatively high hardness and compressive strength. The relationships of the temperature, the current and the axial dimension with the time during the sintering process were further discussed. Additionally, a schematic illustration was proposed to explain the related sintering characteristic of the composites sintered by SPS. The as-synthesized Ti3SiC2/Cu composites were expected to improve the wear resistance of polycrystalline Ti3SiC2.

Preparation and Characterization of Tic-Sic Composites Sintered by Sps

Spark plasma sintering of TiC-based composites toughened by submicron SiC particles

Microstructure and Mechanical Properties of Composites Obtained by Spark Plasma Sintering of Ti3SiC2-15 vol.%Cu Mixtures

Fabrication and mechanical evaluation of SiC–TiC nanocomposites by SPS

Densification and Mechanical Properties of Tic by Sps-Effects of Holding Time, Sintering Temperature and Pressure Condition

Microstructure and Mechanical Properties of Ti3sic2/3y-Tzp Composites by Spark Plasma Sintering

Fabrication And Mechanical Properties Of Al2o3-Ti3sic2 Composites By Sps

Preparation of TiB2–SiC composites toughened with interlocking microstructure by self-assembled TiB2 plates

Microstructure, Mechanical Properties, and Sintering Behavior of Ti3O-Fe2TiO4-TiC Composites

Microstructure and Mechanical Properties of the Spark Plasma Sintered Tac/Sic Composites: Effects of Sintering Temperatures

EFFECTS OF SINTERING PARAMETERS ON TiC/Fe COMPOSITES PRODUCED BY SPARK PLASMA SINTERING

Microstructure And Mechanical Properties Of Sic Ceramic Toughened With Tin Nanoparticles

The preparation of Ti3SiC3/Al2O3 composites by SPS and their properties

Microstructure and Mechanical Properties of TiN/Si3N4 Nanocomposites by Spark Plasma Sintering (SPS)

In-situ synthesis TiC + TiB/Ti composites by spark plasma sintering

Synthesis of W-TiC composite powders by wet-chemical process and its sintering behavior by SPS

The microstructure and deformation behavior of W-SiC composites via spark plasma sintering

Fabrication and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>-Ti<sub>3</sub>SiC<sub>2</sub> Composites by SPS

Microstructure and mechanical behaviour of transient liquid phase spark plasma sintered B4C–SiC–TiB2 composites from a B4C–TiSi2 system

Microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

Microstructure Characterization of the Cu-Ti-C Composites Prepared by Mechanical Alloying and Spark Plasma Sintering