Abstract:WC-Co cemented carbides are widely used in the fields of military, aerospace, mining and cutting industry etc. In this paper, a new two-step method for the preparation of WC-Co cemented carbides was proposed. First, the mixture of yellow tungsten trioxide (WO3) and cobaltic oxide (Co2O3) were reduced by carbon black to remove all the oxygen. Then, the carbothermic reduction products were precisely mixed with an appropriate amount of carbon black to directly prepare WC-Co cemented carbides. The effects of C/WO3 ratio on the phase composition, morphological evolution, particle size and mechanical properties of products are investigated. The experimental results revealed that when the C/WO3 molar ratio was above 2.7, all oxygen in the raw material mixture were removed by carbon black and a mixture of W2C and η-phase were obtained after the first step of carbothermic reduction at 1150 °C for 2 h; then, the mixture of carbothermic reduction product and an appropriate content of carbon black was compacted, and the green compact was first carbonized at 1200 °C for 2 h and then sintered at 1450 °C for 4 h to prepare cemented carbides. With the increase of C/WO3 ratio at the first stage, the content of η-phase with a low melting point increased, which resulted in the large grain size of WC in the finally prepared cemented carbide. Compared with the traditional method of preparing cemented carbides, the cemented carbides prepared by the current method showed a higher hardness and toughness. Furthermore, the addition of a proper content of the VC in the second stage can significantly inhibit the grain growth of WC and further increase the hardness of cemented carbides.

Synthesis of WC-Co Composite Powders with Two-Step Carbonization and Sintering Performance Study

Synthesis of Y2O3-doped WC-Co powders by wet chemical method and its effect on the properties of WC-Co cemented carbide alloy

Microhomogeneous WC-TiC-Co composite powders with enhanced sinterability via a two-step carburization method

Microstructure Evolution and Hardness Improvement of WC-Co Composites Sintered with Fe Substituting Part of Co Binder

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

A short and facile process to synthesize WC-Co cemented carbides

Rapid synthesis of ultrafine WC-Co cemented carbides by in-situ reactions and spark plasma sintering

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Microstructural Characterization of Nanostructured WC-Co Cemented Carbides

WC-18wt.% Co with simultaneous improvements in hardness and toughness derived from nanocrystalline powder

Study on the preparation mechanism of novel WC-Cr2(C, N)-Co nanocomposites

A Novel Method for Direct Synthesis of WC-Co Nanocomposite Powder

WC-Co Composite Coating Deposited by Cold Spraying of a Core-Shell-Structured WC-Co Powder

Enhancement of the mechanical properties of ultrafine-grained WC-Co cemented carbides via the in-situ generation of VC

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

Microstructure and mechanical properties of WC–Co-based cemented carbide with bimodal WC grain size distribution

L1 2 strengthening of WC-CoNiFe cemented carbides by spark plasma sintering

Tracking the evolution of microstructure and phases of WCoB-Co cermets during sintering

Effect of Co on morphology and preparation of in situ synthesis of WC-Co composite powders

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism